Go Back  Quiltingboard Forums >
  • Main
  • Which direction should the fabric be matched for backing? >
  • Which direction should the fabric be matched for backing?

  • Which direction should the fabric be matched for backing?

    Thread Tools
     
    Old 05-03-2011, 09:05 AM
      #1  
    Super Member
    Thread Starter
     
    Join Date: Dec 2010
    Location: Georgia
    Posts: 2,048
    Default

    I have several quilt tops that I inherited that I would like to finish. Most are very simple and I think they will be good practice for both SID and FMQ.

    I also have a lot of fabric and want to use it for the backing instead of purchasing more. So my question is:

    Which is better to have the seam running hortizonal or vertical? I did check some of the ones here and they appear to be vertical (up and down the quilt)

    Thanks for your help
    Vicki W is offline  
    Old 05-03-2011, 09:08 AM
      #2  
    Power Poster
     
    Join Date: Dec 2008
    Location: Western Wisconsin
    Posts: 12,930
    Default

    Traditionally one would buy two lengths of fabric, split one down its length, sew the halves to each side of the whole, and end up with two seams running up and down somewhere on the sides of the quilt. The idea was to keep the seam from being in the center where the quilt would likely experience more stress from folding (and perhaps beard more).

    Nowadays, though, there are no rules. It usually saves fabric to have the seam or seams going from side to side rather than up and down. You can also save fabric by using a diagonal seam. However, with patterned fabrics, it really doesn't matter at all to me.

    Also, many people apply borders to the back, run a diagonal line of blocks down the middle of the back, etc. This can make the back more decorative and also allow for using smaller pieces of fabric.

    For traditional quilts, I still prefer the original method, especially if it's a plain fabric on the back (such as muslin).
    Prism99 is offline  
    Old 05-03-2011, 09:08 AM
      #3  
    Super Member
     
    Maggiemay's Avatar
     
    Join Date: Aug 2010
    Location: NE Ohio
    Posts: 1,541
    Default

    I usually go in the direction that takes less fabric.
    Maggiemay is offline  
    Old 05-03-2011, 09:18 AM
      #4  
    Senior Member
     
    Join Date: Jul 2010
    Location: Rockford, Illnois
    Posts: 393
    Default

    Are you loading this onto a frame to quilt? I only ask because if you are you should lay the seam side to side. Loading it with the seam going up and down will cause the multiple layers of the seam to build up as you roll your quilt causing a ridge down the center of the roll changing the tension on the frame.
    MzMcKee is offline  
    Old 05-03-2011, 09:38 AM
      #5  
    Super Member
     
    Join Date: Jun 2008
    Location: Utah
    Posts: 8,844
    Default

    Originally Posted by Maggiemay
    I usually go in the direction that takes less fabric.
    Same here.
    quiltsRfun is offline  
    Old 05-03-2011, 09:44 AM
      #6  
    Power Poster
     
    Join Date: Feb 2009
    Location: Northern Michigan
    Posts: 12,861
    Default

    being a long arm quilter i always ask that backings be peiced horizontally- that way when the quilt is loaded on the frame the seam runs evenly along the length of one of the bars...if the seam is vertical then in the center of the quilt, with each turn of the bar you build up 4 layers of fabric- in just a few turns you have very baggy/loose side edges because of the bulky buildup in the center.
    if hand quilting it does not matter- and i don't know if it really makes a difference when using your domestic machine- but it makes a huge difference if long-arm quilting
    ckcowl is offline  
    Old 05-03-2011, 09:46 AM
      #7  
    Super Member
     
    JUNEC's Avatar
     
    Join Date: Jan 2010
    Location: Clearwater, FL
    Posts: 2,328
    Default

    Originally Posted by Maggiemay
    I usually go in the direction that takes less fabric.
    That's what I usually do
    JUNEC is offline  
    Old 05-03-2011, 09:56 AM
      #8  
    Super Member
     
    OKLAHOMA PEACH's Avatar
     
    Join Date: Mar 2010
    Location: BLANCHARD, OK
    Posts: 2,502
    Default

    Thank you for your info on the seams, makes so much sense. the horizonal method.
    OKLAHOMA PEACH is offline  
    Old 05-03-2011, 10:01 AM
      #9  
    Super Member
     
    Join Date: Apr 2007
    Location: North Carolina - But otherwise, NOTW
    Posts: 7,940
    Default

    Originally Posted by Maggiemay
    I usually go in the direction that takes less fabric.
    Ditto!! It doesn't matter to me.
    jljack is offline  
    Old 05-03-2011, 12:47 PM
      #10  
    Super Member
     
    Join Date: Jul 2010
    Posts: 1,029
    Default

    I go horizontally side to side and generally add in a stripe of different fabric so it means that I have two seams, but neither are in the exact middle of the quilt when folding. And i love the different "pop" of color.

    Here are two samples of what I did....

    But most of my quilts are less than 72 inches wide....so it works to get 4 yards and cut it into 2 yard pieces.....so they are each 72x44.... and it ends up a bit more than 72 x 88 inches.
    Attached Thumbnails attachment-192444.jpe   attachment-192445.jpe  
    luvspaper is offline  
    Related Topics
    Thread
    Thread Starter
    Forum
    Replies
    Last Post
    platyhiker
    Main
    13
    12-09-2017 04:03 AM
    RosMadeMe
    Main
    9
    05-30-2013 06:56 AM
    AlwaysQuilting
    General Chit-Chat (non-quilting talk)
    2
    04-28-2011 04:53 PM
    craftybear
    Links and Resources
    9
    01-05-2011 01:10 PM
    craftybear
    Links and Resources
    2
    10-08-2010 05:57 AM

    Posting Rules
    You may not post new threads
    You may not post replies
    You may not post attachments
    You may not edit your posts

    BB code is On
    Smilies are On
    [IMG] code is On
    HTML code is On
    Trackbacks are Off
    Pingbacks are Off
    Refbacks are Off



    FREE Quilting Newsletter