Foot Pedal rest for sewing machine
#23
Senior Member
Join Date: Jul 2015
Posts: 594
The grid pattern shelf liner works for me on a pretty plush carpet. Just a piece about 4" by 8". It may slowly creep but not bad at all. The grid shelf liner works so well for so many things. I use a 6" or so square of it to get a grip on jar lids; I put small pieces under microwave feet to keep it from inching backward every time I slam the door.
I have used it to make a gripper surface on the underside of a chair caddy (to hold magazines, remote and such) to name a few uses. You can buy it at the Dollar Store for very little.
I have used it to make a gripper surface on the underside of a chair caddy (to hold magazines, remote and such) to name a few uses. You can buy it at the Dollar Store for very little.
#24
My foot pedal slipped around on our carpet no matter what I used under it.
So my husband took a piece of pegboard that we had around and cut it to length as follows.... the foot pedal was where I wanted it for comfort and the edge of the board was under the edge of the pedal and the far edge of the pegboard reached to the baseboard. Then he glued velcro to the bottom of the foot pedal (two places) and stapled the matching velcro piece to the pegboard. This holds the pedal securely.
My intent for travelling was to take the pedal off and put some spare velcro over the foot pedal stuff to keep it clean. But when I went to a retreat recently I just took the whole shebang as it fit easily in my travel bag.
If you need pictures please let me know and I'll see if I can get some and transfer them to the computer to send.
So my husband took a piece of pegboard that we had around and cut it to length as follows.... the foot pedal was where I wanted it for comfort and the edge of the board was under the edge of the pedal and the far edge of the pegboard reached to the baseboard. Then he glued velcro to the bottom of the foot pedal (two places) and stapled the matching velcro piece to the pegboard. This holds the pedal securely.
My intent for travelling was to take the pedal off and put some spare velcro over the foot pedal stuff to keep it clean. But when I went to a retreat recently I just took the whole shebang as it fit easily in my travel bag.
If you need pictures please let me know and I'll see if I can get some and transfer them to the computer to send.
#26
[ATTACH=CONFIG]611261[/ATTACH][ATTACH=CONFIG]611262[/ATTACH]
First photo is of the control on the floor. I had to pull it over the heat register to get a picture without shadows, usually it sits to the side.
Second picture is of the foot controller upside down and the board showing the Velcro. My intent was to cut the pegboard into a narrower strip, just haven't gotten around to it.
First photo is of the control on the floor. I had to pull it over the heat register to get a picture without shadows, usually it sits to the side.
Second picture is of the foot controller upside down and the board showing the Velcro. My intent was to cut the pegboard into a narrower strip, just haven't gotten around to it.
#27
Senior Member
Join Date: Feb 2010
Location: Austin, TX
Posts: 847
Years ago there was a member here on Quilting Board, and she (or her husband) made out of wood a foot rest, and the way it was made, the foot petal set upon it. It was a solution for sure, and I always was intending to order it from her, but never got around to it. So long ago, have no clue as to her name, but I think she was in the Killeen, TX area but that may not be correct either.
#28
Super Member
Join Date: Jan 2012
Posts: 4,783
I solved the problem by buying an inexpensive floor mat from the dollar store that was large enough to completely fill the space under my sewing desk kneehole (or a bit larger and could be trimmed down). Then I determined the most comfortable place on that mat for my foot pedal, traced around it and cut that hole out of the mat. Put the pedal into the hole made for it and it doesn't travel at all. The mat extends to the sides of the desk from left to right and all the way back to the baseboard. If your mat is too thin and the pedal slips out (like mine did), glue strips of mat (from what you trimmed off to make it fit) all around the hole to make it thicker in that area only. My strips are about an inch wide. Easy, inexpensive fix, and quick.
#29
Super Member
Join Date: Mar 2011
Location: in the sticks of PA
Posts: 2,313
Actually those videos of Vanessa with Jenny are from years ago. Vanessa is just getting ready to open a everything store, fabric, classes for garments as well as quilting, she is offering rental time on a longarm as well. So if you are in the Gainesville, FL area you can stop by. I believe the opening is in May some time.
#30
Super Member
Join Date: May 2012
Location: Central Wisconsin
Posts: 4,391
Thanks, GEMRM. That looks doable and looks like it would work well. I could make mine so it just fits under the table between the legs and would be contained by those legs so it wouldn't slide around. Maybe it could have holes for the table legs to fit into. I would need help to get that done and undone though.
Thread
Thread Starter
Forum
Replies
Last Post
joobee
For Vintage & Antique Machine Enthusiasts
9
04-07-2014 06:04 AM
Treasureit
Links and Resources
56
07-21-2013 07:33 AM