Frustrated - ready to give up fmq
#21
Super Member
Join Date: Jul 2010
Location: Central Willamette Valley, Oregon, USA
Posts: 7,695
I read all the suggestions, but one idea was missed. Your needle might have a burr. Even with all the quality controls needle companies have (and they take pride in the product they make) sometimes you get a bad needle. Try replacing it? I find a bad needle about once every few years. I just accept it as a cost of doing business. Also, make a sample sandwich to test on, until it works right. (I make my test samples all 12.5" in certain colors, so I can use them in QAG)
#22
Super Member
Join Date: Aug 2010
Location: Upstate New York
Posts: 1,231
Before you start messing with the adjustments on your machine..try going slowly...slow machine speed, slow hand movements. I think most people watch the videos of the professionals and don't realize that they have longarms and stitch regulators..us mere mortals need to start slowly till we get the hang of it!
#23
When I have those days I do this: Make sure you have a clean machine. Rethread even though you know it is threaded right, change my needle to a denim #16. If you are already using a 16 then put a new 16 in. Put stitch length to "0" One of those things usually fixes it in my experience. You will get lots of good advice so hopefully someone can help
#25
Super Member
Join Date: Jul 2014
Location: Illinois
Posts: 2,140
Lots of great suggestions here! One other thing...
Make sure when your thread breaks to clip the thread up by the spool & then pull the thread from the needle down to remove the cut thread. That will help pull out any little fuzzies in the thread run. I got a tiny grey fuzzy caught in my thread run the other day & the thread snapped. Sure enough, when I pulled the cut thread down, the fuzzy came out. I rethreaded my machine & was good to go. You might even try doing that a couple of times before you start up again. It will clean any tiny fuzzies or bits of thread out to ensure it travels smoothly to your needle.
Make sure when your thread breaks to clip the thread up by the spool & then pull the thread from the needle down to remove the cut thread. That will help pull out any little fuzzies in the thread run. I got a tiny grey fuzzy caught in my thread run the other day & the thread snapped. Sure enough, when I pulled the cut thread down, the fuzzy came out. I rethreaded my machine & was good to go. You might even try doing that a couple of times before you start up again. It will clean any tiny fuzzies or bits of thread out to ensure it travels smoothly to your needle.
#27
Super Member
Join Date: Jul 2012
Location: Vancouver Island, Beautiful BC
Posts: 2,090
OP Breathe, as you can see by reading all the replies many of us, probably most of us have had this problem at one time or another.
I have not seen this comment.
My 20+ year old Kenmore - made by Janome - always shreds thread if I mix poly and cotton thread. It was never the needle, tension, threading, just a mix of thread types. Of course I forget at times, but she reminds me pretty quick.
I have not tried mixing thread types on my new Janome 2030.
I have not seen this comment.
My 20+ year old Kenmore - made by Janome - always shreds thread if I mix poly and cotton thread. It was never the needle, tension, threading, just a mix of thread types. Of course I forget at times, but she reminds me pretty quick.
I have not tried mixing thread types on my new Janome 2030.
#28
I also would say, I try to avoid seams. Some threads have weak places in them. Look close at the thread after it has broken. I pull off about 12 or more inches. Be sure to relax, that helps too. The more often you FMQ the better you will get. Just keep trying and you will get it.
#29
Super Member
Join Date: Aug 2013
Posts: 9,299
Most teachers will strongly recommend you draw, draw, draw on paper to practice . Fill a sketchbook (use big, cheap tablets). You have to build muscle memory and that only comes with repetition. I say all this as one who was on the verge of giving up, too, nit long ago. Then I started on solid color sandwiches, and now I am getting the hang of it and ....drumroll please... really liking it. You can do this!
#30
Give your machine a good cleaning - the bobbin area, take it apart to get all the lint out. A new needle frequently helps. And remember, it's not a race. Take your time and move it along slowly!
Thread
Thread Starter
Forum
Replies
Last Post
Ps 150
Pictures
129
07-01-2022 08:33 AM
Snorky Lvs2Quilt
Main
16
04-21-2011 09:57 PM