Hanging a quilt...advice
#1
Hanging a quilt...advice
I have a 50" x 50" quilt I would like to hang on a wall. I've checked out the you tubes for making a sleeve but was wondering if there are any tips anyone can give me to help make it a success? I'm yet to bind this quilt and wonder if I should be approaching the binding method in a different way to get a nice flat binded edge? Should I press the quilt before hanging? Any advice would be appreciated.
#2
Super Member
Join Date: Aug 2013
Location: Florida
Posts: 5,967
My favorite way to hang a quilt at home is to put a sleeve on the back at the top and the bottom. Binding is done the usual way and the sleeves don't interfere with the bindings. I then use cafe curtain rods. The brackets only stick out about and inch from the wall. I hang it using a small rod with finials sticking out on the sides. Then I hang a second rod in the bottom sleeve with the finials sticking out on the bottom. But the bottom isn't attached to the wall and is lightweight enough to hang and pull the quilt down and straight. Pressing is not necessary. The bottom rod hold it straight.
#4
Senior Member
Join Date: Jun 2009
Location: Woburn, MA
Posts: 711
I always just staple my quilts to the walls, all four sides in the binding seam. The staples make the smallest of holes in the wall (you can barely notice) and I don't have to add sleeves. You can flatten out the wall hanging and it staple down to lie flat. Good luck with whatever method you use.
#6
I cut a piece of lathe (which is ¼ " x 1 ½ " approx) to the width of the quilt. Find the centre and measure and drill holes, out 7 ½ " each way so that I always have 15" between the two nail holes. (then different wall hangings can be hung from the same two nails) Mark on the wall where you want the holes to be and hammer in two nails. I make a three part sleeve and hand sew it to the back of the quilt. Insert the lathe piece into the sleeve and slip the two holes onto the nails. It hangs very flat to the wall.
#7
Super Member
Join Date: May 2011
Location: Pacific NW
Posts: 9,563
Binding: Do not iron the binding in half lengthwise before attaching it to the quilt. That is my best advice.
Hanging sleeve: Make sure your sleeve sits on the quilt in the shape of a D. The flat part of the D is up against the back of the quilt, and the rest of the sleeve should not sit flat against the quilt. That way when you hang it, the quilt will hang nice and smooth, and won't bulge out in front of the hanging rod.
Hanging sleeve: Make sure your sleeve sits on the quilt in the shape of a D. The flat part of the D is up against the back of the quilt, and the rest of the sleeve should not sit flat against the quilt. That way when you hang it, the quilt will hang nice and smooth, and won't bulge out in front of the hanging rod.
#9
Senior Member
Join Date: Feb 2011
Location: Philomath,Ore
Posts: 499
The two times I used command strips, they took the paint off the wall. You can easily add a sleeve and sew if down as you machine sew the binding to that side of the quilt, then either whip stitch or safety pin the bottom of the sleeve. I sometimes also add a bottom sleeve if the quilt it not lying flat
#10
Super Member
Join Date: Jul 2013
Location: Houston, TX
Posts: 9,735
My favorite way to hang a quilt at home is to put a sleeve on the back at the top and the bottom. Binding is done the usual way and the sleeves don't interfere with the bindings. I then use cafe curtain rods. The brackets only stick out about and inch from the wall. I hang it using a small rod with finials sticking out on the sides. Then I hang a second rod in the bottom sleeve with the finials sticking out on the bottom. But the bottom isn't attached to the wall and is lightweight enough to hang and pull the quilt down and straight. Pressing is not necessary. The bottom rod hold it straight.
Thread
Thread Starter
Forum
Replies
Last Post
thequiltmama
Main
38
05-24-2011 12:57 PM