HST question
#1
HST question
I know that if I want a 3 1/2 square I should cut it 7/8 more or round up to 1" more. However i made a test square and cut 2 4" squares and drew a line diagonal and sewed 1/4 from the line on each side of line and cut in the middle and pressed and I got a 3 and 5/8 sq. Is that to little to sq up. or should I go for the 4 in square to start with? Another thing I wand to know is there a quick way to make a 4 patch. I sewed two 2'' inch strips together and then sub cut in 2 " and sewed two back together to get a 3 1/2 sq 4 patch. Thanks for your help. When you read the book and sit down to make test blocks, it is entirely different. The book is telling me to do bias strips for the HST and I don't like the instructions so I am doing it the draw a line way.
#3
Senior Member
Join Date: Jan 2013
Posts: 307
Hi, Sewing Suz....I'm also in Arizona. The only way I will make my HST is by using the Easy Angle ruler. You cut your strips the size that you want your HST to be. No guess work and they come out perfect. Sew....if I want a 3 12 inch HST, I cut a 3 1/2 inch strip and use the ruler and sew them together. Easy peasy!
Last edited by pokeygirl; 02-14-2018 at 06:16 PM.
#4
3 5/8 is still larger than your needed size and can still square it up. Just take a little from one side, flip and square to size needed. If you are still testing, the rests of your blocks you can cut a little bigger to give you more wiggle room. And, I make 4P the same way but others might pipe in with a different technique.
I always substitute easier sewing techniques than offered in patterns. That's the quilter is us!
I always substitute easier sewing techniques than offered in patterns. That's the quilter is us!
#5
Cutting 4" square should be enough but it depends on how you sew
and what type of thread you use. If the thread is thick it will take
more space in the seam allowance. If you sew right on the line
or next to the line it makes a difference. The only way to find out
is to press and trim. If you find you can't trim to 3.5" square
then cut the square bigger or adjust your seam allowance a little.
You are right on track for the 4 patch. That's the way I know to
make quick 4 patches. If you have lots of 4 patches to make
in the same fabric, you just cut two long strips, sew then sub-cut.
and what type of thread you use. If the thread is thick it will take
more space in the seam allowance. If you sew right on the line
or next to the line it makes a difference. The only way to find out
is to press and trim. If you find you can't trim to 3.5" square
then cut the square bigger or adjust your seam allowance a little.
You are right on track for the 4 patch. That's the way I know to
make quick 4 patches. If you have lots of 4 patches to make
in the same fabric, you just cut two long strips, sew then sub-cut.
#7
Super Member
Join Date: Aug 2011
Location: kansas
Posts: 6,407
sounds like you have this figured out already. But I just a couple of weeks ago (where???) saw a tute that said to be sure to press open each seamed "corner" of those HST and then to open and make sure to use the iron point to press on the straight of grain. Said to Not use the side of the iron to open the seam and press (what I'd been doing) cause it's on the bias and can distort the seam with a curve instead. Makes perfect sense and works, too!
#9
Hi, Sewing Suz....I'm also in Arizona. The only way I will make my HST is by using the Easy Angle ruler. You cut your strips the size that you want your HST to be. No guess work and they come out perfect. Sew....if I want a 3 12 inch HST, I cut a 3 1/2 inch strip and use the ruler and sew them together. Easy peasy!
Thread
Thread Starter
Forum
Replies
Last Post