I HATE binding
#21
Power Poster
Join Date: May 2008
Location: MN
Posts: 24,666
Originally Posted by LucyInTheSky
Originally Posted by dunster
I do it exactly like your teacher says. If you're cutting 2.5 inches, it will make .5 inch wide double binding this way. You need to line the edge of the binding up with the edge of the top, not the edge of the back and batting. Then you do need to sew carefully, and straight.
#22
What's difficult with having the extra 1/4" of non-quilt is that it's hard for me to tell if I'm sewing 1/4" onto the quilt top. That's part of why I like what y'all said about cutting things right to the quilt top since then (in theory) it should be substantially easier to get to 1/4" onto the quilt top... No reason in making binding more complicated then it needs to be :mrgreen:
#23
Ditto. My top, batting and back are all squared the same. My binding strips are 2 1/4". I don't know who you took your class from, but I've never heard of it done that way before.
Originally Posted by raksmum
I square up my quilt having the backing, batting and top all the same (I don't make the backing/batting larger). I lay the raw edge of the binding right up to the raw edge of the quilt and sew 1/4". When you flip to the back to sew it down it should be fine. If you find you have excess when you flip it to the back then cut your binding strips 2 1/4" instead of 2 1/2".
Hope this helps.
Hope this helps.
#24
Power Poster
Join Date: May 2008
Location: MN
Posts: 24,666
Originally Posted by LucyInTheSky
What's difficult with having the extra 1/4" of non-quilt is that it's hard for me to tell if I'm sewing 1/4" onto the quilt top. That's part of why I like what y'all said about cutting things right to the quilt top since then (in theory) it should be substantially easier to get to 1/4" onto the quilt top... No reason in making binding more complicated then it needs to be :mrgreen:
#25
Originally Posted by bearisgray
Can you move your needle to a left-hand position? That might help a bit.
#27
Power Poster
Join Date: Mar 2009
Posts: 15,639
I square the quilt and then I pin the binding with an even distance to the edge. My preferred method is continuous binding, so I only pin one side at a time. Then I finnagle the corner and continue. It is not show quality, but I have had no complaints and I have never had the problem you described.
#28
From what I have been told, quilt binding should be "full", meaning that the batting completely fills the binding. Judges check for that, but more important the binding lasts longer and looks better if it's full.
I prefer the look of .5" binding and would use .25" only on very small wall hangings, but this is just my personal preference. I think some judges prefer thin binding. That doesn't matter to me, since I don't intend to submit any quilts for judging. As long as your method gives a full binding with consistent width, the method doesn't matter too much. You do need to select a strip width that matches your method though. I use your teacher's method with 2.5" strips, and I don't pin. I do use the walking foot, and my walking foot also allows any needle position.
I prefer the look of .5" binding and would use .25" only on very small wall hangings, but this is just my personal preference. I think some judges prefer thin binding. That doesn't matter to me, since I don't intend to submit any quilts for judging. As long as your method gives a full binding with consistent width, the method doesn't matter too much. You do need to select a strip width that matches your method though. I use your teacher's method with 2.5" strips, and I don't pin. I do use the walking foot, and my walking foot also allows any needle position.
#29
Super Member
Join Date: Aug 2007
Location: Clay Springs AZ
Posts: 3,229
Wow, never heard of that problem before.
I dont cut off my batting or backing until I have sewn the binding onto the front of the quilt. 1/4 inch onto the quilt top. I dont see how you can get a good mitre on the corner if you sew a larger seam.
I also machine sew in the ditch on the front to attach the back binding.
This is after I Elmer glue the binding to the back side No hand sewing for me.
Have never pined the binding to the front either and just stretch it a small bit as I sew it to the front of the quilt.
But I do square up my quilt top before I layer and quilt.
I dont cut off my batting or backing until I have sewn the binding onto the front of the quilt. 1/4 inch onto the quilt top. I dont see how you can get a good mitre on the corner if you sew a larger seam.
I also machine sew in the ditch on the front to attach the back binding.
This is after I Elmer glue the binding to the back side No hand sewing for me.
Have never pined the binding to the front either and just stretch it a small bit as I sew it to the front of the quilt.
But I do square up my quilt top before I layer and quilt.
#30
Senior Member
Join Date: Nov 2006
Posts: 786
I'm thinking I'm going to cut my batting/backing to the quilt top size, no excess. What size binding strips do you cut? When I did 2.5" and did this, it gave me waaaaaaaay too much on the back. I'm thinking 2" should be enough (1/4 sewed down, 1/4 showing on top, 1/4 on side 1/4 on back, x 2 strips = 2")??
Lucy, (sorry, I couldn't get the "quote" to work)
I wouldn't make the binding strip less than 2 1/4". You have to remember once you fold it in half, you have half the width. Then place the raw edge to the raw edge of the quilt and sew 1/4". When you flip to the back it will "fill" with the edge of the quilt and you won't have excess.
Lucy, (sorry, I couldn't get the "quote" to work)
I wouldn't make the binding strip less than 2 1/4". You have to remember once you fold it in half, you have half the width. Then place the raw edge to the raw edge of the quilt and sew 1/4". When you flip to the back it will "fill" with the edge of the quilt and you won't have excess.
Thread
Thread Starter
Forum
Replies
Last Post
craftybear
Links and Resources
3
12-25-2010 09:49 PM