If your ruler has been used a lot - - -
#11
Power Poster
Thread Starter
Join Date: May 2008
Location: MN
Posts: 24,581
#12
![Default](/images/icons/icon1.gif)
I'm so glad this topic came up. I've been using two 5x24" rulers for yrs. & had never considered that happening. I had to check them & find they are still flat. No curve. I have sliced little knicks off the edges with rotary cutter but have affected their use.
Thanks for bringing this up. I will now ck. them once in awhile.
Thanks for bringing this up. I will now ck. them once in awhile.
#14
Super Member
Join Date: Sep 2010
Location: Myrtle Beach, SC
Posts: 8,126
![Default](/images/icons/icon1.gif)
Very glad your cutting problem is resolved. However, I am confused by this sentence,
"When I finally set it on a straight surface - like my kitchen counter - I could see that my ruler was making a shallow arch".
I retired a craft table that was a great space saver because it had two roomy hinged leafs. After the pressure from countless cuts, the leaves curved downward from the center (where the support was) to the edge of the leaves. It took me a long time to figure out why my cuts all curved. The cutting mat was curved to the shape of the top of the leaves, too.
New ruler, new cutting mat and using the dining room table solved the problem. Thank God!
"When I finally set it on a straight surface - like my kitchen counter - I could see that my ruler was making a shallow arch".
I retired a craft table that was a great space saver because it had two roomy hinged leafs. After the pressure from countless cuts, the leaves curved downward from the center (where the support was) to the edge of the leaves. It took me a long time to figure out why my cuts all curved. The cutting mat was curved to the shape of the top of the leaves, too.
New ruler, new cutting mat and using the dining room table solved the problem. Thank God!
#16
Super Member
Join Date: May 2012
Location: Central Wisconsin
Posts: 4,391
![Default](/images/icons/icon1.gif)
Wow, I would never have expected to have that happen.
I did noticeably wear out the starting corner on one of my rulers. So now when using the rotary cutter I don't begin at the end of the ruler (and slice off the corner). Instead I begin ahead of the corner a bit, roll backwards just to the end of the ruler, then forward with the cut.
I did noticeably wear out the starting corner on one of my rulers. So now when using the rotary cutter I don't begin at the end of the ruler (and slice off the corner). Instead I begin ahead of the corner a bit, roll backwards just to the end of the ruler, then forward with the cut.
If you push in from the edge, the pile of fabric is likely to wrinkle up from the pressure.
#19
![Default](/images/icons/icon1.gif)
I think some of the plastic that they use in making rulers is softer than others. I have a favorite ruler that needs to be replaced as my new rotary cutter has shaved some filings off the side.
Marcia
Marcia
#20
![Default](/images/icons/icon1.gif)
When I first read this posting early this morning, I pooh-poohed the idea. I've been cutting and sewing all day. Just now, while waiting for my iron to heat up I decided to hold the edge of my ruler vertically against my dining room table. Well, no more pooh-poohing from me! The middle of my ruler swings easily back and forth while the ends stay flat. I would never have thought this could happen. Luckily I have a new 24" ruler that I bought when Hobby Lobby had a huge coupon. Thanks so much to the original poster!
Thread
Thread Starter
Forum
Replies
Last Post
bearisgray
Main
31
06-23-2016 08:38 AM
pinkcastle
Main
10
07-07-2012 12:19 PM
lindamar
Main
18
09-20-2011 06:50 AM