Keeping fabric tight when quilting
#1
Member
Thread Starter
Join Date: May 2007
Posts: 17
I have tried used quilting pins (safety type), basting with thread, ironing after doing this and I still am having a problem with when I go to quilt the whole piece, that I have puckers in the back on the fabric. No matter how flat I get the back, smooth out the batting, then iron and smooth out the top, I have a problem. I have spray but haven't used it yet, as you have to have ventalition and it's expensive. I am so frustrated that I spend more time taking out the mess I have made and this in turn makes me unhappy about the whole process. Can anyone give me a hint? thanks.
#3
Junior Member
Join Date: Jan 2007
Location: Wilmington, NC
Posts: 282
Even after you've pinned or basted the layers together sometimes it needs redoing. If you start quilting in the middle and work your way out, then when you come to a point when it starts slipping here and there take your pins out and adjust then repin. Always allow extra batting and backing for just in cases. Hope this helps. Also if your ironing don't iron back and forth, this will stretch the top. Press going up and down.
#4
i use the spray and pins also, just make sure to open the window and don't just stay there and do the whole thing at one time, do a little, take a break and walk outside for a couple of minutes then go back and do some more. your back will appreciate it too. just use a light spray on the backing then put the batting on top and a lite spray on it then put on the top. it takes a while to get it all done but it's worth it.
#5
I am working on a lap quilt now and part of it was hand quilted and part machine quilted. I agree, the spray is the way to go. It amkes it so much easier, evn if you pin afterwards, helps keep the slipping to a minimum!
#6
Yup... Spray lightly then pin... Works 99.9% of the time. The good thing about the spray is if you notice slippage after a few days of working on the same projuct, just use your iron to press (not slide) the area where the fabric has turned loose and the spray is re-activated.
Good luck! Don't let it frustrate you, & PLEASE don't give up. The problem you are having is not uncommon, but easily fixed.
Hope this helps... If not, come back... We'll just try to make you laugh instead of helping you quilt. Some days, one is just as good as the other!! :D
Good luck! Don't let it frustrate you, & PLEASE don't give up. The problem you are having is not uncommon, but easily fixed.
Hope this helps... If not, come back... We'll just try to make you laugh instead of helping you quilt. Some days, one is just as good as the other!! :D
#7
Member
Join Date: Nov 2006
Posts: 31
You didn't say how or where you are layering your quilt. I know for sure if you do not fasten the back layer down securely you will get puckers every time. I have unbased a few times my self. I do like the spray baste, just open a window and turn on a fan for a little while.
#8
I spray baste and the spray I use holds great.. no need for pins.. no slippage.. and it lasts until the quilt is washed! I have sprayed a quilt, rolled it up and let it sit for a week before I was able to start quilting it and it did great!
I actually baste mine outside. I have done it on my patio. Cleaned it off and covered with a kingsize sheet. Now I use 3 folding tables. Much easier on the back!
Barb C.
I actually baste mine outside. I have done it on my patio. Cleaned it off and covered with a kingsize sheet. Now I use 3 folding tables. Much easier on the back!
Barb C.
#9
My way is probably not the most desirable to most people but I will gladly share my methods... I have hardwood floors, so I lay my backing down and use masking tape to keep it secure and taut (not stretched). Then spray the backing, roll out the batting, spray again, then roll out the top. I use a 4 ft. long, 1" wooden dowell to smooth each layer before spraying, which works great & saves the back & knees. (this is a trick I learned while working in a uniform manufacturing company spreading out the fabric for the pieces to be cut from) If it is a quilt larger than a full size, I will pin baste in addition to the spray because it takes me more than a couple of weeks to complete the quilting. On a full or smaller I just use the spray.
Thread
Thread Starter
Forum
Replies
Last Post
ArtisticDesign
Main
18
09-29-2010 08:30 AM