Aly

I am a complete beginner and as my first simple project am creating a baby quilt that I plan to only tack by machine, not quilt fully. But I am such a newbie I don’t even know how to get to that stage. I have two questions I’m hoping you experts can help me with:

1. When pinning the quilt sandwich together, what kind of pins do I use? Can I use my straight pins down through and back up again or ? I’m worried the layers will shift during that process.

2. How do I ensure that my lines of tacking are straight and evenly spaced? I read somewhere that I should start in the middle, is that correct? Then what?

I realize for the experienced these are pretty silly questions but I really want my project to turn out…perfectly (ha, not likely as a beginner, I know!) so I’d be grateful for every bit of advice I can get.

Thank you!

HeatherY

If you pin, you should use safety pins. Lay everything out, push the pins through and back up but don't close them yet. Once you've pinned the quilt- think every 6 inches or whatever seems to work- then close the pins. If you need to move them it'll be easier and they won't pull for as much distortion.

You ought to baste around the whole quilt before starting the quilting.

QuiltnNan

they are not silly questions at all.
if straight pins are all that you have, you certainly can use them. however, they could fall out or you can seriously jab yourself with them. curved safety pins for quilters is the best choice. i'd found mine at walmart.
to make things evenly spaced and straight, you should mark your quilt top. you can use washable Crayola markers, or i sometimes just use a sliver of soap. there are also other markers ... just read the package to make sure it is the method you want to use because afterwards, you'll have to remove the marks.
keep us updated on how you do.
and welcome to the board.

cjsews

You can get safety pins that have a bend in them. The bend is so the come back up easily. Or you could to a basting stitch throuth the layers. Start in the middle when quilting so that if the layers shift you do not end up with a pucker in the middle of the quilt. You can smooth the layers outward as you go in needed. To mark your quilt, there are may tools. Water soluble pens, air soluble, chalk. Use a ruler to mark evenly.

Good luck and welcome to quilting.

bunniequilter

You can also thread baste your quilt. Not the most popular method compared to saftey pins, but does the job just as well. I go the hand route when it comes to basting, I baste everyting by hand.

Tartan

Safety pins are safer and more secure than straight pins. You can use lines of masking tape or ainter's tape to space your tacks. You might want to search the web for a video on pin basting a quilt to get some visual pointers.

DOTTYMO

Using the curved pins, there are cheap and expensive ones. I have found the more e xpensive pins have a better point and tend not to leave such large holes. Always start in the centre and work outwards. The one point no one has mentioned is making the sandwich. Put the right side of backing on the flat surface you are using. And tape down with a little tension then place the wadding on top laying if flat without stretching use fingers only. Now put top on right side up. Again lat flat with fingers and pin from centre. Keeping flat pin every 6 inches. You will use a great deal of pins. Back and wadding should be larger than top on all sides. PM is need more advice on this as it is important not to get wrinkles in back.

grammy Dwynn

Most of us, use the floor (not carpeted) to pin our quilts. Tape down the back (right side facing floor), tape down ~ smooth and tight, but not stretched. Followed by batting, smoothed out. Finally top, centered on other two layers. LQS suggested to use your fist (fingers in and heal of hand down) to measure the distance apart of your pins, saves time from physically measuring. Better to over-pin, then having fabric shift. I also use bent quilters pins.

Good luck and cannot wait to see your completed project.

bigsister63

There are med size curved safety pins that are best to use. Do not use the big one since they will leave big holes. Also there is a thing called "Kwik-pin "(?) that will make closing the pins easier and save your fingers. Joanns sells it for about $10 but you can use a coupon making it really worth the $$$. (some people use spoons). I personnaly use 505 spray basting since the sandwich will really not shift. Also start from the middle and work out. Also alternate the direction of you stitching so help with no puckering. When you are say tacking what do you mean. Depending on the size of your block you may be able to do SID and have the quilting the correct distance apart. I ususally do SID with invisible thread so the stitching is not as noticible. If you need to do addition stitching such as diagona. you can use blue painters tapr. it is cheap and comes up easily and not leave sticky residue. The tape comes in a variety of widths so you can stitch lines on either side of it to secure quilting. Such as if you want lines 1 1/2 part use that width tape. If you want side by side lines than the tape is a good method. also another suggestion is to stitch on either side of the seams the same distance apart to secure. The package of batting should tell you haw far apart you quilting should be. Be sure to follow this recommendation as the manufacture knows best.

pocoellie

Personally, I hate pinning, I would rather spray baste or thread baste. You would mark where you would tack before hand. There are no stupid or silly questions. We all have to learn some way and if we don't ask questions, how would we learn, you can't learn everything out of a book or by UTube videos.