Power cord from the ceiling for your longarm?
#11
Member
Join Date: Aug 2016
Posts: 67
Peasco, I'm intrigued by the shelf you have under your frame that the UPS sits on. My UPS currently sits on a box, but I would love to put it on something more sturdy. Can you either explain how it was installed or provide additional photos?
#12
Member
Join Date: Jan 2014
Posts: 11
[ATTACH=CONFIG]606931[/ATTACH][ATTACH=CONFIG]606933[/ATTACH]I used 2 L-shaped shelf brackets (one for each leg), 4 (2 for each leg and bracket) what I called U-bolts, it when I was at the hardware store I saw they had a square bolt as you can see in the pictures. Figured the square shape would fit tighter around the leg. 1 piece of plywood long enough to fit between the legs and wide enough to hold the UPS. I wanted to get the UPS off the floor so I could clean more easily under the longarm. I don’t have as much hand strength as I used to so asked a friend to tighten the U-bolts. Men can really tighten bolts well. Had wanted to paint the plywood, just don’t see it to remind me to get that little job done.
#13
Member
Join Date: Aug 2016
Posts: 67
[ATTACH=CONFIG]606931[/ATTACH][ATTACH=CONFIG]606933[/ATTACH]I used 2 L-shaped shelf brackets (one for each leg), 4 (2 for each leg and bracket) what I called U-bolts, it when I was at the hardware store I saw they had a square bolt as you can see in the pictures. Figured the square shape would fit tighter around the leg. 1 piece of plywood long enough to fit between the legs and wide enough to hold the UPS. I wanted to get the UPS off the floor so I could clean more easily under the longarm. I don’t have as much hand strength as I used to so asked a friend to tighten the U-bolts. Men can really tighten bolts well. Had wanted to paint the plywood, just don’t see it to remind me to get that little job done.
After reading your post I rushed out to DH's shop and found a shelf and two brackets left over from another project, and even have square u-bolts, but they were too small. I have the zip ties for the cord. And found some angle braces that i can screw to the top side of the board, and the UPS can be secured so it doesn't shift from the table vibrations ( i assume that's why you have yours strapped to the frame leg?)
So a quick stop at Ace Hardware tomorrow for the right size bolts and i'm all set.
Thank you again for sharing your wonderful idea.
#14
Super Member
Join Date: Jul 2010
Location: Glenmoore, PA
Posts: 7,941
My longarm is in my living room, out a couple feet from the wall. I have a surge protector and extension cord that travels along with the machine. Since I am not back there often, the dragging cord is no problem for me. But in my finished basement, when I had it finished off I requested a ceiling outlet for my iron, over my large ironing table. I love it, only wish I had thought to have it connected to the main light switch so the iron would turn off when the light is turned off.
#15
Member
Join Date: Aug 2010
Location: Virginia Beach, VA
Posts: 26
I took Electricity in 4H one year and made for my project a heavy-duty extension cord for my mother's iron. Her washer, dryer and iron/ironing board were in the basement. The extension card was plugged into an outlet between the floor joists above, and had a large cup hook above the ironing board to keep the extension cord out of the way when not in use.
I estimate that this was in 1962 and that I was eleven year's old. Mama used this set-up until she moved into an assisted living facility 4 years ago. The new occupants of the house are still using it.
It's good to know how useful this idea was and how long it has lasted.
I estimate that this was in 1962 and that I was eleven year's old. Mama used this set-up until she moved into an assisted living facility 4 years ago. The new occupants of the house are still using it.
It's good to know how useful this idea was and how long it has lasted.
#16
Super Member
Join Date: Jul 2010
Location: Central Willamette Valley, Oregon, USA
Posts: 7,695
When we built my sewing studio, we had two electric outlets put in the ceiling and two in the floor. When my longarm was set up a week ago, I soon discovered that it would be difficult to put a surge protector in the ceiling so I’m using the floor plugs and they are conveniently under the machine so I don’t have cords to step over anything. I guess the ceiling outlets might come in handy if I need to add a light bar or something...
BTW- new surgery protectors are now made to plug in flush to the wall, so that type might work for you. (You can support the cord in place with a couple cup hooks.)
Last edited by madamekelly; 01-18-2019 at 10:53 AM.
#17
Member
Join Date: Nov 2011
Location: Northern Alabama
Posts: 5
Such great ideas here on the board. Love the pictures too. My solution to not tripping over the cords especially when concentrating on the quilt, machine, pattern, radio, etc. is quite simple. My teenage granddaughter simply brought over a roll of duct tape (bright neon orange) and roughly wrapped the cords. It's just enough for me to see out of the corner of my eye and certainly has prevented me from not only tripping but crashing into the sun-room windows. Hey, when I trip I tend to crash like a bull in a china shop. It has worked for over 4 years now.
#18
Super Member
Join Date: Nov 2010
Location: Littlefield, TX, USA
Posts: 1,077
Long arm cord suspention
I like this idea! Trying to figure a way to get my cords off the floor.
Yes, I had my electrician install a wall socket up in my rafters so I wouldn't trip over the cords. I also added a metal ring onto a galvanized pole so the cords can move with the machine. Here's a pic of my setup. Its not pretty but I haven't tripped yet. I also have a camera on my quilt machine, automatic advancement for the back roller as well as robotics so more cords to worry about so all up in the rafters.
Thread
Thread Starter
Forum
Replies
Last Post