Preparing to Make a Quilt Question
#31
Sometimes I cut all my pieces first but most of the time I make a sample block & then cut my pieces as I go. Not long ago I decided to make the Over & Down Under Quilt by Bonnie Sullivan and as I read the pattern & did some research on making it, I found that I should cut all my pieces first as this quilt takes some organization & numbering of pieces concerning the color placement. Well, it's a good thing I cut all at once because I had to put it aside after cutting/numbering all the pieces instead of starting it right away & I would have never remembered where I left off if I had not cut all at once. I'll pick it back up when time permits.
Last edited by osewme; 06-28-2019 at 01:44 PM.
#33
I cut as I go so that if I want to make changes midstream I can do so. One time I began cutting several pieces in the beginning and found I was cutting the wrong size. Stopped right then and there and have never cut everything first. I like to have the option to change my mind on which fabric to use where. Make sense?
#35
Super Member
Join Date: Aug 2010
Location: Tampa Bay Area, Florida
Posts: 2,229
I love reading our similarities and differences, so reassuring to remind myself there are several paths to the same destination! Complicated block, I cut one and assemble first, more simple I cut all that is needed. I do not cut my borders until blocks, rows, whatever are assembled and blocked, and binding when the top is completed and blocked.
#36
Power Poster
Join Date: May 2008
Location: MN
Posts: 24,666
Before I cut anything, now I soak it in hot water, wash, dry, and iron/press the fabric.
I used to "just" give the fabric a quick wash in tepid (lukewarm) water, and then dry it. I would always iron/press the fabric before cutting it. I have learned that sometimes it takes a bit of time (like at least 30 minutes) before some excess dyes will release.
If I am following a pattern, I make sure I have enough of whatever it calls for before starting. I may make changes as I go, so I probably would not cut out everything at once.
I had been "taught" to cut the borders before cutting the center pieces. I ruined a large piece of fabric doing that - I was a beginner beginner then, and was not that aware of "the bigger picture" when looking at the designs in a fabric.
Another "learn and live" lesson.
I do think it makes sense to "set aside" border fabric - especially if the borders are wide and one "should be" aware of how the pattern will "hit" on the strips.
I used to "just" give the fabric a quick wash in tepid (lukewarm) water, and then dry it. I would always iron/press the fabric before cutting it. I have learned that sometimes it takes a bit of time (like at least 30 minutes) before some excess dyes will release.
If I am following a pattern, I make sure I have enough of whatever it calls for before starting. I may make changes as I go, so I probably would not cut out everything at once.
I had been "taught" to cut the borders before cutting the center pieces. I ruined a large piece of fabric doing that - I was a beginner beginner then, and was not that aware of "the bigger picture" when looking at the designs in a fabric.
Another "learn and live" lesson.
I do think it makes sense to "set aside" border fabric - especially if the borders are wide and one "should be" aware of how the pattern will "hit" on the strips.
#37
Power Poster
Join Date: Feb 2009
Location: Northern Michigan
Posts: 12,861
It really depends on the project. Most times I cut as I go along, once in a while I cut everything out in the beginning. I usually want to cut out one block or one section first just to make sure it comes out right. Sometimes there are misprints or mathematical errors I want to catch before I cut out a lot. Quite often I make my quilts up as I go along so I’m cutting as I go and finding fabrics as I go too
#38
Senior Member
Join Date: Aug 2015
Location: Ranger, Texas
Posts: 788
It's interesting to read the different methods we use. I once precut a lot of pieces for a mystery QAL. As we assembled & I realized the pattern, I wanted a few more blocks to enlarge the overall size & pattern. I cut more pieces, then they didn't fit with the original cuts! I must have been slightly 'off' in my measurements the second time. As a result, I'm more likely to precut all pieces at the same time now. Except for sashing. The width may be decided by amount of fabric I have.
#39
Senior Member
Join Date: Feb 2010
Location: Austin, TX
Posts: 847
Thread
Thread Starter
Forum
Replies
Last Post