Originally Posted by ckcowl
ok, i guess i am missing something here. if you are zig-zagging the batting together why are you using fusable too? seems like a waste...i would think one or the other would be the way to go, if you are stitching then don't waste the fusable; but i thought the original post was from someone who did not want to sew her batting pieces anymore. the problems with fusing the edges are: bulk if you overlap the pieces; stiffness along the seam; gumming up the needle when quilting (depending on what fusable was used) pressing such large pieces and getting them to stay together until you get it quilted. if you just go with the zig-zag it is done and going to hold up without lumps/bulk/stickiness/ problems with it not holding.
Originally Posted by QuiltswithConvicts
I lay W&N pieces overlapping just a little bit and trim both layers. Remove the slivers & butt the big pieces together. Lay the interfacing over the joint and press. I use steam and an applique sheet (just because I have one) but you could use a scrap of muslin to keep the glue off your iron. THEN - I take it to my machine. Turn it over so that the fusible is on the bottom and zig-zag the joint. I use as wide a zig-zag as my machine does and a fairly open length. I like to reinforce the fusible - kinda like the fusible is holding everything together so you CAN sew it together.
I use this method to put ALL my scrap W&N together into a usable size, I don't like to throw it away. By using the fusible before I sew, I have a much nicer, smoother joint and I'm not fighting with the 2 pieces of batting to play nicely together while I stitch them. I guess I don't trust just the fusible to hold, especially if an area where the fusible is doesn't get quilted enough to hold everything together. It's just what I do. |
As a "motion and time study" person (remember the days when we did that in business?) I would think that zig zagging takes a lot less time than fusing. Other reasons not to fuise has been mentioned above. I would also think that the heat while fusing packs down the batting and will give a different look on that section when quilting. Having said that, try it on a crib size quilt and see how it works.
|
Originally Posted by dunster
I am tired of stitching batting together, but my bolt of batting is 90" wide and my quilt top is 102", so something must be done. I picked up some Pellon lightweight fusible interfacing, and I'm going to try fusing the batting pieces together. I'm using W&N batting. I will be quilting on my longarm. The plan is to cut 1.5" strips of the interfacing and apply to the batting - but that's as far as I've gotten in the thought process.
I have some questions. Should I cut off the side edges of the batting before using it? Should I put a cloth (damp or otherwise?) over the interfacing (which is laid on top of the seam in the batting) before applying the iron? Should I fuse both sides together? Anything else I should know? This interfacing was cut off a bolt and didn't come with directions, so I would appreciate advice from anyone who has already done this. TIA |
just remember the interfacing is'nt permanent. you need to quilt over that area or go ahead and sew it together.
|
Originally Posted by Cyn
I just zig zag mine.
|
Originally Posted by dojo36
i would use 505
Thank you everyone for your comments/suggestions. I plan to work on it today. |
Originally Posted by dunster
Originally Posted by dojo36
i would use 505
Thank you everyone for your comments/suggestions. I plan to work on it today. |
Ok, I think I understand - so you don't sew it together or fuse it together, just let the spray hold the batting in place and quilt over it? I'm quilting on a longarm, and it's a big quilt, so I don't think that method would work for me, but it does show that once the quilting is finished, the batting being stitched together is probably not necessary. I know that when I whip-stitch it the stitches are easily pulled apart (if I pull on it), but once quilted there is no problem at all.
Originally Posted by dojo36
Originally Posted by dunster
Originally Posted by dojo36
i would use 505
Thank you everyone for your comments/suggestions. I plan to work on it today. |
Originally Posted by dunster
Ok, I think I understand - so you don't sew it together or fuse it together, just let the spray hold the batting in place and quilt over it? I'm quilting on a longarm, and it's a big quilt, so I don't think that method would work for me, but it does show that once the quilting is finished, the batting being stitched together is probably not necessary. I know that when I whip-stitch it the stitches are easily pulled apart (if I pull on it), but once quilted there is no problem at all.
Originally Posted by dojo36
Originally Posted by dunster
Originally Posted by dojo36
i would use 505
I don't understand how this would help. Thank you everyone for your comments/suggestions. I plan to work on it today. |
All times are GMT -8. The time now is 03:54 PM. |