Red Snapper type loading systems
#1
Senior Member
Thread Starter
Join Date: Oct 2013
Posts: 673
Red Snapper type loading systems
I must be the weakest person in the world. I can't physically squeeze the red snapper type clamps onto the leader.
I can load the backing on the table at the back of the machine. I use my whole self to push it on. But the ones at the front that you basically have to squeeze with your fingers I can't do.
I guess it's pinning for me.
I can load the backing on the table at the back of the machine. I use my whole self to push it on. But the ones at the front that you basically have to squeeze with your fingers I can't do.
I guess it's pinning for me.
#2
Member
Join Date: Jan 2015
Location: Northwest Arkansas
Posts: 65
Are yours new? Maybe you need hold one end down and then bend the other end upward toward the end you are holding down to open up the channel. I did this to mine and that seemed to help. Also I had my husband cut the long ones in half to make smaller pieces. They are easier to deal with for me. Hope this helps you.
#3
Power Poster
Join Date: Dec 2010
Location: Michigan
Posts: 11,276
I have the same issue. Not much problem on the back, but an issue on the front. They are softer & easier to apply if they are warm. You can try using a blow dryer to make them more pliable. They usually supply some short 2" pieces. Can you use those in the front? If you can, cut up one or more of the long clamps into small pieces. I cut mine down to 1", although I sometimes still just pin the front.
#4
Senior Member
Thread Starter
Join Date: Oct 2013
Posts: 673
I have the same issue. Not much problem on the back, but an issue on the front. They are softer & easier to apply if they are warm. You can try using a blow dryer to make them more pliable. They usually supply some short 2" pieces. Can you use those in the front? If you can, cut up one or more of the long clamps into small pieces. I cut mine down to 1", although I sometimes still just pin the front.
I know there's probably a learning curve to getting the hang of them, but honestly it feels like I need another pair of hands.(strong ones) Between holding everything in place and then pushing the clamp on.
I was ready to relearn my loading process, but then the issue of not having the finger strength thwarted my enthusiasm.
Maybe pins aren't so bad.
Also, how often should the needle be changed? Can't seem to find any info.
Last edited by sval; 01-12-2017 at 09:04 AM. Reason: forgot
#5
Power Poster
Join Date: Dec 2010
Location: Michigan
Posts: 11,276
Yes, small pieces across the front. I find this quicker than pinning. DON'T go cutting one up until you try a small piece! I always use the snappers on the back. It depends on how long my backing is as to what I do on the front.
if i have just a small amount of extra backing, I pin. If lots, I use the snapper pieces. The small pieces may bump against the edge of the machine, especially if you are using a ruler base.
if i have just a small amount of extra backing, I pin. If lots, I use the snapper pieces. The small pieces may bump against the edge of the machine, especially if you are using a ruler base.
#6
Power Poster
Join Date: Dec 2008
Location: Western Wisconsin
Posts: 12,930
I had the same problem. My dh and I took one of the mid-sized pieces to the hardware store and went to the dowel section. There we found wooden dowels that were just slightly bigger than the red snappers. (I brought my dh to make sure *he* could put the red snapper on the bigger dowel.) We bought half a dozen dowels. This step is not necessary, but when we got home my dh had me soak the red snappers in hot water in the bath tub; he said it would soften the plastic. We wiped them dry, and he placed them on the dowels. I left them that way for a week (actually longer because I forgot them, but a week should be enough). It's been awhile since I used them, but I remember I was able to load a practice quilt myself after that. The red snappers will eventually loosen with use, but I just couldn't wait that long -- especially since I don't do many quilts in a year.
#7
I lift one end up as I'm pressing down, but I'm not a fan, I will stick with pinning, but I do loveeeeeeeeeeee my side snappers, did I mention just how much I love my side snappers??? A LOT...........for me, sometimes tried and true is best, my hats off to those that can use the snappers and zippers to load a quilt.
#8
Super Member
Join Date: Aug 2011
Location: kansas
Posts: 6,407
I use them on front and back and love them--and they will lose their stiffness if used. You can use a blow dryer to soften them until that happens. I use the small 2" ones to center the quilt and "tack" down the section I' working on, then attached the longer snapper as I remove the little ones. I use 3 long ones front & back. I always attached the center first and then do the 2 ends(that are using different snappers). Also, I always leave the snappers on the rods on the leaders which helps too. also, someone suggested to use the heel of your hand and push the snapper on using the bar as the hard surface to push against instead of your fingers and hand.
#10
I don't use my fingers at all. I use the heel of my hand and wedge it on using the belly bar as leverage. I also have found that I can leave a small (inch or two) gap between the ends of the snappers. I will have a friend over tomorrow to sew if you want a picture.
Thread
Thread Starter
Forum
Replies
Last Post