Reduce Labyrinth Walk
#1
Reduce Labyrinth Walk
I bought the Labyrinth Walk pattern and fabric to make it but I'd like to do it as a throw. The pattern is for a queen. Has anyone reduced it or know how to? I do not have EQ. Engineer hubby resized it by calculations and formulas but I can not cut to the 32nd of an inch. It is not the kind of pattern that blocks can be removed from as it is only 9 large blocks and they are all part of the design. Any help would be greatly appreciated.
http://www.quiltmag.com/resources/la...rn-correction/
http://www.quiltmag.com/resources/la...rn-correction/
#2
Super Member
Join Date: Jun 2010
Location: The Deep South near Cajun Country, USA
Posts: 5,434
That quilt is on my bucket list. I think the theory for reducing but keeping all the same blocks is to calculate the percentage you want it to be and multiply that percentage by each number on the pattern.
example.... if the blocks measure 24 inches finished and you want to reduce it. Figure out what size you want the block. Easiest is to make both of them divided by either 8 or 3. If you make the blocks 16", then you would reduce the measurements by 1/3. 24 x .333 = 7.992 24-8 (you round up the 7.9) gives you a 16 inch block. Or you could just multiply 24 x .667 = 16.008" finished. If you do decide to reinvent all your pattern numbers, I would use those numbers to cut paper to the sizes you think they should be, less the 1/4" stitching on all the sides and tape it together to see if it will fit. This way you can make any corrections prior to starting the quilt. If you use colored paper, you will be able to see the pattern emerging.
After looking at the pattern again...you are going to have a heck of a time with some of the smaller lines. I would think about making it a 2x2 block square and adding extra borders if needed to get you to the size you wanted. This is one where it was made 2x3 blocks, probably to fit a twin/full https://search.yahoo.com/search;_ylt...yfp-t-252&fp=1
example.... if the blocks measure 24 inches finished and you want to reduce it. Figure out what size you want the block. Easiest is to make both of them divided by either 8 or 3. If you make the blocks 16", then you would reduce the measurements by 1/3. 24 x .333 = 7.992 24-8 (you round up the 7.9) gives you a 16 inch block. Or you could just multiply 24 x .667 = 16.008" finished. If you do decide to reinvent all your pattern numbers, I would use those numbers to cut paper to the sizes you think they should be, less the 1/4" stitching on all the sides and tape it together to see if it will fit. This way you can make any corrections prior to starting the quilt. If you use colored paper, you will be able to see the pattern emerging.
After looking at the pattern again...you are going to have a heck of a time with some of the smaller lines. I would think about making it a 2x2 block square and adding extra borders if needed to get you to the size you wanted. This is one where it was made 2x3 blocks, probably to fit a twin/full https://search.yahoo.com/search;_ylt...yfp-t-252&fp=1
Last edited by Barb in Louisiana; 08-24-2015 at 08:56 PM.
#5
Super Member
Join Date: Jun 2010
Location: The Deep South near Cajun Country, USA
Posts: 5,434
Thanks for mentioning this. I have gotten so use to using EQ7 to recalculate block size that I forget about deducting the seam allowance first.
#6
They way i do any block i'm figuring out (don't buy patterns myself) is with graph paper. Get yourself a book of graph paper ( 1/4" grid is usually easiest to work with) and some colored pencils and duplicate one of the squares (noting the individual pieces in different colors) on the graph paper. Then YOU decide what size each of the graph paper grids squares are for your quilt ..... say you decide each one represents 2 inches.... that will give you your finished sizes for each individual piece - add your quarter inch and you have your pattern piece sizes....which you can then make yourself.
Best of luck.
Best of luck.
#7
The pattern is for 84"x84", which is too small for a queen bed IMHO. What size do you want it to be? As you've already discovered, changing the size for this quilt will be much harder than usual. If hubby remembered the seam allowance subtraction requirement, I think I would just go with his calculations, measuring as closely as possible to the 1/32nd inch. With each unit that you assemble, check against what hubby calculates that unit should measure. I also have the pattern, and I also would like to make it smaller, but probably as a wall hanging rather than a throw. That is if I ever get around to it...
#9
Super Member
Join Date: Jun 2012
Location: Sonoma County, CA
Posts: 4,299
There are a few spots on this quilt (in the pattern) where the lines aren't right. It bugs me every time someone makes this quilt but nobody else ever mentions it so I wonder if it's just me? Do you guys see the weird spots?
It still looks neat in the pattern and even cooler as a quilt, but my eyes are immediately drawn to the weird areas whenever I see one in person.
It still looks neat in the pattern and even cooler as a quilt, but my eyes are immediately drawn to the weird areas whenever I see one in person.
Thread
Thread Starter
Forum
Replies
Last Post