Square corners
#1
Super Member
Thread Starter
Join Date: Jul 2015
Location: Indiana
Posts: 1,497
Square corners
What method do you use to get square corners on your finished quilt? After it has been quilted and you are about to add the binding, what have you been doing? Do you mark or trim the top only? The top and batting? All of it? I have also heard to trim the batting 1/4" bigger than the top.
#2
Power Poster
Join Date: Feb 2009
Location: Northern Michigan
Posts: 12,861
I lay out my quilted quilt and draw with Taylor’s chalk a straight line , squaring corners and straightening all 4 edges. Then I place my binding along the straight lines and stitch it on. Next I trim a 3/8” wide seam allowance and finish my binding. This process works for me. Many Quilters have tried many different suggested techniques- then use the one that works best for them.
#3
I place the quilted quilt on the rotary mat and square it up with my large square up ruler. since I cut my binding at 2.25", I don't have a problem with having to leave extra batting to make the binding full.
#4
Power Poster
Join Date: Nov 2009
Location: Mableton, GA
Posts: 11,355
#5
Super Member
Join Date: May 2017
Location: Sunny Florida
Posts: 4,434
I use the 20" square up ruler and another long ruler lined up together on the quilt edge. Square up the quilt edges and trim. The second ruler helps me make sure the sides will continue square.
Binding is cut at 2.5". I sew the binding on the back of quilt with a 3/8 seam.
Like ckowl, I found that 3/8" is the magic number for having binding equal on both sides.
I have also used 2.25 " binding like Quilt Nan.
All the methods work due to the math.
Make a sample and try the different widths of binding with different seam allowances. You will find your magic spot.
Binding is cut at 2.5". I sew the binding on the back of quilt with a 3/8 seam.
Like ckowl, I found that 3/8" is the magic number for having binding equal on both sides.
I have also used 2.25 " binding like Quilt Nan.
All the methods work due to the math.
Make a sample and try the different widths of binding with different seam allowances. You will find your magic spot.
#6
Power Poster
Join Date: Mar 2011
Location: Ontario, Canada
Posts: 41,548
I always square up my quilt after it is quilted. If it is a large quilt, I do it flat on my kitchen floor. I place my 2 large squares in the corners of one side and place my long rulers between them. This is to make sure that the corners are truly square and the side is perfectly vertical between them. I place my large rotary mat underneath and trim, moving the mat as needed. I work my way around the whole quilt. If it is a small quilt, I do it on my table.
I cut my binding at 2-1/4 inches and sew it to the front of my quilt. I do nice corners ( many good videos on YouTube) and join up my ends. I press the binding and turn it to the back of the quilt for hand sewing.
I cut my binding at 2-1/4 inches and sew it to the front of my quilt. I do nice corners ( many good videos on YouTube) and join up my ends. I press the binding and turn it to the back of the quilt for hand sewing.
#7
Super Member
Join Date: Feb 2011
Location: Yorkville, IL
Posts: 7,639
I also square up after it is quilted. My sunroom floor is ceramic tile and really works well. I work similar to Tartan but I prefer 2 1/2” binding sewn on the top by machine, pressed and hand sewn on the back. I hate to admit this but it is getting harder and harder to get up off the floor. Lol
#8
Power Poster
Join Date: May 2008
Location: MN
Posts: 24,666
I also use a large square on each corner to trim - after it is quilted.
I cut all three layers even -
I cut a 2-7/8 to 3 inch wide binding - that finishes to a scant 1/2 inch.
Like some others, I also line up the whole quilt so that all four corners have 90 degree angles.
Sometimes I mark - I usually don't.
I cut all three layers even -
I cut a 2-7/8 to 3 inch wide binding - that finishes to a scant 1/2 inch.
Like some others, I also line up the whole quilt so that all four corners have 90 degree angles.
Sometimes I mark - I usually don't.
#9
Super Member
Join Date: Aug 2018
Location: Greater Peoria, IL -- just moved!
Posts: 6,183
I square my top before I quilt, once it is quilted I keep as is.
I have my backing and batting larger than my top, machine sew on my binding and using that seam as a reference trim the back and batt to 1/2". I cut my binding a bit wider at 3" and I like a full binding.
Almost all the time I use French fold continuous bias binding, sew on to the the front by machine, miter the corners, flip and hand stitch down the back.
I have my backing and batting larger than my top, machine sew on my binding and using that seam as a reference trim the back and batt to 1/2". I cut my binding a bit wider at 3" and I like a full binding.
Almost all the time I use French fold continuous bias binding, sew on to the the front by machine, miter the corners, flip and hand stitch down the back.
Thread
Thread Starter
Forum
Replies
Last Post
nativetexan
Main
28
10-19-2013 08:37 PM