Is there a foot to achieve a SCANT 1/4 inch seam??

Reply Subscribe

Page 6 of 7

« First

Thread Tools

09-02-2011, 02:44 PM

#51

incoming2me

Senior Member

Join Date: Nov 2010

Location: Indiana

Posts: 745

Quote:

Originally Posted by watterstide

Quote:

Originally Posted by incoming2me

I have several low shank machines and use this foot for all my piecing.

I don't think I could piece without it!

this foot has the single hole..so if you move your needle to far, you could break the needle or worse,bend the shaft.

Very true!
However, my low shank machines are vintage Singers and only have a straight stitch..
no optional needle positions. :)

09-02-2011, 06:06 PM

#52

sylviasmom

Senior Member

Join Date: Mar 2010

Location: Pueblo, Co

Posts: 663

You can purchase a Little Foot. Made of plastic with red markings. There are two models, one snaps on and the screws on.

09-02-2011, 06:23 PM

#53

Bjbaxter

Senior Member

Join Date: Feb 2011

Location: Philomath,Ore

Posts: 499

I use "mole skin" for blisters, and just cut a strip and is has a self stick back. It stands about 1/8" tall, the the fabric butts up against it. Or you can use multiple layers of painters tape.

09-02-2011, 06:29 PM

#54

Grandma Mary

Senior Member

Join Date: Mar 2011

Location: Michigan

Posts: 757

I was taught by a quilting teacher to buy the thick "mole skin" pad that is found in the Dr. Scholl's area of your local store. It comes in a rectangle that's about 1 and1/2" x 3". It is sticky on one side. Cut out a strip along the 1&1/2" side that's about a 1/4" wide. I use a ruler and my rotary cutter to get a straight, clean cut. This gives you a small "wall" to lay down on your scant quarter inch line from your foot toward you on your machine. Then, when you are piecing, just line the edge of your fabric with that edge while you are sewing. The thickness of the "skin" makes it so that your fabric stays inside that line. I hope this is making sense to you. It works really well, and when your skin starts to wear out, you can pull it off. You will have plenty of extra to keep cutting more pieces.

OOPS! Just realized that the reply above said the same thing! Sorry for the repetition!

09-02-2011, 07:56 PM

#55

Greeter Eva

Senior Member

Join Date: May 2010

Posts: 466

Quote:

Originally Posted by LoriJ

I use the Angler 2 from Pam Bono. It goes out far enough to the front that I can line up a scant 1/4 inch very easily. My piecing is perfect when I use it.
http://pamsclub.com/index.php?catego...hk=1&Itemid=71

I have a question about using the "Angler 2". What do you use to attach it? I would have to remove it , every time my bobin needs changing. Is there an easy way to do this?

09-03-2011, 03:22 AM

#56

watterstide

Super Member

Join Date: Oct 2009

Posts: 5,453

yes, you will have to remove it to replace the bobbin. i have never used it myself though...

09-03-2011, 03:46 AM

#57

lisalovesquilting

Super Member

Join Date: Dec 2009

Location: Ohio

Posts: 2,929

Quote:

Originally Posted by GagaSmith

I have a Janome 6300 and I adjust the width to 4.5 and use the 1/4 inch foot and it gives me a scant 1/4 inch.
It's just where you can adjust the stitch length and width. I assume your machine has that feature.

Yes. I believe all Janomes do. Look in your manual. I have a 6600 and set it to 5.8. Good luck. :D

09-03-2011, 06:24 AM

#58

LoriJ

Senior Member

Join Date: Aug 2008

Location: Raleigh, NC

Posts: 700

Quote:

Originally Posted by Greeter Eva

Quote:

Originally Posted by LoriJ

I have a question about using the "Angler 2". What do you use to attach it? I would have to remove it , every time my bobin needs changing. Is there an easy way to do this?

I have my machine in a table. When I need to change the bobbin, I slide the clear filler portion to the left, leaving the angler attached, then move it back. Before I had this, I used blue painter's tape to reduce stickyness, stuck the angler to my machine and unstuck what I needed inorder to lift the angler enough to reach in at change the bobbin. Or you could remove it completely each time if you wanted. As long as you keep the "key" portion, it is real easy to remove and replace the angler as needed. I take it off completely when I am paper piecing or FMQ.

Attached Thumbnails

09-03-2011, 06:35 AM

#59

cattailsquilts

Senior Member

Join Date: Jul 2010

Location: Eidson, TN

Posts: 559

Quote:

Originally Posted by piepatch

You can get a magnetic seam guide at Hancock's that is "thick" enough to keep your fabric from shifting over it. It is better than using a post it note, or tape or moleskin. Of course your machine base would have to be metal for the magnetic guide to hold. I have only seen them at Hancock's, but you might find them in other fabric shops.
http://www.hancockfabrics.com/Magnet...VVviewprod.htm

Just be careful if you have a computerized machine. While it may not actually cause any damage, chances are pretty good that if it did, you are out good money to have it fixed.

09-03-2011, 10:39 AM

#60

watterstide

Super Member

Join Date: Oct 2009

Posts: 5,453

The magnet on the bottom of the machine, or on the bed, is no where near the "brain" of the machine. it would do no harm there.
they now have magna-hoops for the bernina Emb sewing machines..

Quote:

Originally Posted by cattailsquilts

Quote:

Originally Posted by piepatch

Just be careful if you have a computerized machine. While it may not actually cause any damage, chances are pretty good that if it did, you are out good money to have it fixed.