Trouble with 'dog legs' when cutting strips - help?
#21
Senior Member
Join Date: Apr 2010
Location: Lived in San Diego now retired in Eagar, AZ.
Posts: 887
I fold twice and use the june tailor strip cutter...the crux of the problem is not folding along the grain...get rid of the selvedges, they will put the fabric off-grain, and then hold the fabric up in the air, folding raw selvedge edges together...if a 'fold' is showing, off-kilter, then align the raw edges till it hangs straight...for the fold to lie straight is more important than for the ends to be even...move the sides till the fold is flat. Now fold in half again and do the same thing...they must hand straight when folded to cut straight. Now line up the bottom fold on a line of your cutting mat...lay strip cutter on top and line up the big black line even with the bottom fold line.... cut as many strips as you like, if the folds were straight, the strips will be straight. When cutting several pcs of cloth, i offset them by 1/2" or so... then they will cut better and straighter. it also allows you to go 'up and over' the folded edge so they will not cause you to go offline. I love this tool so much, I bought the 36" version when it was on sale just so i didn't have to move it so often... I use it ALL the time...
#22
Power Poster
Join Date: Mar 2011
Location: Ontario, Canada
Posts: 41,548
Using a large square may help you in getting straight cuts. Lay your fabric with the fold at the top on your cutting board. Make sure the fabric is smooth and lay the lg. square along the fold. Cut your strips on the side of the square making sure to keep the top of the square right on the fold.
#24
Super Member
Join Date: Jun 2008
Location: British Columbia
Posts: 2,362
The most important factor is how the fabric is folded in half. technique for folding to make sure the fold is on the straight. I've adapted a bit but basically start with fabric selvage to selvage. Look for a 'bubble' (easiest done if you're a pre-washer and after ironing). I lay the fabric flat on my cutting table with the fold closest to me and then smooth out the 'bubble'. At that point the selvages will not line up but your fabric will be folded straight. Trim off the wonky end and start measuring from there. Haven't had an issue since.
#27
Power Poster
Join Date: Dec 2008
Location: Western Wisconsin
Posts: 12,930
http://www.purlbee.com/rotary-cutter-tutorial/
#28
I went looking for it and the largest I could find was a 20x23" but it only cuts 2 1/2" strips. I have the Shape Cut Plus which cuts 12" strips but allows you to cut across 18" of fabric.
Thanks,
Cathy
#29
Junior Member
Thread Starter
Join Date: Sep 2011
Location: Plymouth Michigan
Posts: 146
I want to thank you all for the great ideas, and a special thank you to Izy for the suggestion to watch the Leah Day video.
This is a wonderful group and always willing to help those of us who are new to the quilting world. Your kindness is overwhelming!!!!
janie
This is a wonderful group and always willing to help those of us who are new to the quilting world. Your kindness is overwhelming!!!!
janie
#30
Super Member
Join Date: Jan 2011
Location: Nawth o' Boston
Posts: 1,879
I align with the cutting mat line at the fold, but I also re-check it at every cut, and I verify my eyeballing the fold lineup against the mat by lining up with my 12" sq ruler shoved against the cutting ruler. When I go to cut I slide it sloooooowwwwwly and gently away from the cutting ruler. I also use a binder clip on the far end of the ruler so it doesn't slip that little 1/8 as you get to the end where you are reaching farther and more likely to go astray with the cut.
If my cut did go astray, I re-line it up, then shave it back into a perfect 90 degrees before the next cut.
Whew.
If my cut did go astray, I re-line it up, then shave it back into a perfect 90 degrees before the next cut.
Whew.
Thread
Thread Starter
Forum
Replies
Last Post
nevrn
Main
3
02-05-2011 09:42 AM