need help what am I doing wrong
#11
Super Member
Join Date: Aug 2009
Location: United States
Posts: 2,222
I use a stlleto, toothpick, long straight pin - whatever - to hold the fabric/ quide it - the last inch or so - the holder is almost under the needle as that last bit is sewn.
some say that using a single hole needlrplate also helps. the downside to using that is to straight stirch ONLY - otherwise one ends up with broken or bent needles.
some say that using a single hole needlrplate also helps. the downside to using that is to straight stirch ONLY - otherwise one ends up with broken or bent needles.
#12
Some machines are easier than others to sew a perfect 1/4" seam. I have a Pfaff, Bernina, Brother and Baby Lock. I really think it has to do with the feed dogs, to some degree.
Do you mind telling us what machine you are using?
I have found with my Baby Lock and Brother, I can get a more uniform, even, and consistent 1/4". I use a standard (J) foot, and set the needle to the 5.5 position for a scant 1/4", and 6.0 for a full 1/4". I have found that I sew much better on these machines.
I think using a full foot, and the feed dogs really do help. But this is only my opinion.
Hope this helps.
Do you mind telling us what machine you are using?
I have found with my Baby Lock and Brother, I can get a more uniform, even, and consistent 1/4". I use a standard (J) foot, and set the needle to the 5.5 position for a scant 1/4", and 6.0 for a full 1/4". I have found that I sew much better on these machines.
I think using a full foot, and the feed dogs really do help. But this is only my opinion.
Hope this helps.
Last edited by Girlfriend; 12-16-2014 at 09:50 AM.
#13
Power Poster
Join Date: Jun 2011
Location: Southern California
Posts: 19,127
I tend to do the same things. Try what Eisy suggest. I have multi layer of painter's tape and try to keep the fabric against the tape to keep it straight. It is amazing how little you can be off and it really does make a difference.
#15
Get yourself a stiletto ( tooth pick, chop stick, pointed pencil, seam ripper) Slow down your sewing speed, really slow and use the stiletto as a guide to keep the fabric near the seam guide and your fingers away from the needle. Also using a scrap to sew onto at the end of a seam will help keep the seam straight.
peace
peace
#16
Power Poster
Join Date: Jan 2011
Location: Southern USA
Posts: 16,426
This was how many instructors in a lot of workshops I have taken have said to do it. I put my finger on the left edge of the foot about an inch before the end and my seams never veer.
#17
Super Member
Join Date: Jun 2010
Location: The Deep South near Cajun Country, USA
Posts: 5,434
I had the same problem you are experiencing. I couldn't seem to correct it. I bought a couple of different 1/4" feet and I still tailed off at the end.
I sew on 2 different Brother machines - a sewing/embroidery combination and a Brother Runway Wally World edition.
A friend recommended I buy an open toed foot that was a snap-on. That started me getting better. I use the left needle stitch setting, then change the width a bit and run the material even with the inside of the right part of the open toe foot to get my 1/4". Then I had to learn to slow down and watch the edge of the material all the way through the foot. I'm not perfect, but I am a whole lot better.
Another thing that really helped me sew straighter was some paper piecing I did. In order to stay on the line, you had to watch it closely. Getting even a little bit off caused some resewing. After you sew the same thing 10 or 15 times, you began to pay more close attention to keeping the edge of the material next to the edge of the foot all the way through the seam.
This is the foot I bought. It is a generic, so doesn't have the fancy markings on it, but I quickly found I didn't need them anyway. http://www.ebay.com/itm/Snap-on-Meta...item3f2f9b1159
I sew on 2 different Brother machines - a sewing/embroidery combination and a Brother Runway Wally World edition.
A friend recommended I buy an open toed foot that was a snap-on. That started me getting better. I use the left needle stitch setting, then change the width a bit and run the material even with the inside of the right part of the open toe foot to get my 1/4". Then I had to learn to slow down and watch the edge of the material all the way through the foot. I'm not perfect, but I am a whole lot better.
Another thing that really helped me sew straighter was some paper piecing I did. In order to stay on the line, you had to watch it closely. Getting even a little bit off caused some resewing. After you sew the same thing 10 or 15 times, you began to pay more close attention to keeping the edge of the material next to the edge of the foot all the way through the seam.
This is the foot I bought. It is a generic, so doesn't have the fancy markings on it, but I quickly found I didn't need them anyway. http://www.ebay.com/itm/Snap-on-Meta...item3f2f9b1159
#18
Banned
Join Date: Aug 2014
Location: Victorian Sweatshop Forum
Posts: 4,096
Originally Posted by bearisgray
I use a stlleto, toothpick, long straight pin - whatever - to hold the fabric/ quide it - the last inch or so - the holder is almost under the needle as that last bit is sewn.
some say that using a single hole needlrplate also helps. the downside to using that is to straight stirch ONLY - otherwise one ends up with broken or bent needles.
I have one straight stitch plate that goes on 6 or 7 of my machines. They are older mechanical machines. I use a small refrigerator magnet on the front of whatever machine has the ss plate on it so I don't forget and switch it to zz. I used to break a couple needles a week but haven't broken any since I started doing this.
Cari
I use a stlleto, toothpick, long straight pin - whatever - to hold the fabric/ quide it - the last inch or so - the holder is almost under the needle as that last bit is sewn.
some say that using a single hole needlrplate also helps. the downside to using that is to straight stirch ONLY - otherwise one ends up with broken or bent needles.
Cari
#19
Super Member
Join Date: Jul 2010
Location: Central Willamette Valley, Oregon, USA
Posts: 7,695
Two things. Sounds like you are using a leader scrap, you should also use an ender to sew off onto. Second. don't, watch the needle, watch the fabric as it feeds against your foot or whatever you are using for a gauge. It's not too hard if you are sewing straight pieces, but you need to be more careful if you are sewing triangles or other shaped pieces. A stiletto helps.
#20
Senior Member
Join Date: Dec 2010
Location: Northern, Utah
Posts: 973
The magnetic guide is great if you don't have an electronic machine. They have been known to ruin the computers in some expensive electronic machines. The magnet is not good for them. You can measure the 1/4 inch and place several layers of blue painters tape at that mark and use that for a guide all the way from front to back. Good luck.
Thread
Thread Starter
Forum
Replies
Last Post