Quarter of an Inch
#21
Senior Member
Join Date: Apr 2010
Posts: 696
Years ago, 40 something, I took basic sewing lessons from a great teacher. If you could sew a shirtwaist dress with cuffs and collar, you could sew any garment. I tailored for years, 5/8" seam allowance. I was taught by her to concentrate on the seam allowance, not the needle. Then I started quilting. I had to get that 1/4" seam allowance. I used white adhesive tape, used with bandages. I taped that down to my machine and I had no more trouble. You know the needle is set because you started to sew, then watch your seam allowance because the sewing will continue until you stop. I did not have any more trouble. And I have 7 machines but I am not telling anyone. No one saw that in this writing. haha
#22
Junior Member
Join Date: Dec 2012
Posts: 110
Nobody has mentioned the quilter's "scant" 1/4 inch. I find that most patterns really mean to use a scant 1/4 inch seam. This measurement takes into account the needle size and thread width of your particular set up. I have learned that using my 1/4 foot but sewing a slightly less 1/4 inch seam works best for me. By slightly less, I mean maybe a thread or couple of thread widths less than 1/4 inch. If you measure your finished size, I think you might be happier. I have never used Bonnie Hunter's tool, but I have thought about purchasing one just to have when changing machines. Try sewing slightly less, a "scant" measurement and see if this helps. Hope it does!
#23
Super Member
Join Date: Mar 2011
Location: Central NJ
Posts: 5,572
I bought a 1/4" foot with guide specifically for my Viking at one point thinking it would help. Not! I have a 'scant 1/4' setting on my machine that works much better. Returned the foot. I also am of the school that keeps my finger on the left edge of my foot and gently guide my fabric through. I also agree that consistency is usually far more important than precision 100% of the time.
#24
Super Member
Join Date: Aug 2007
Location: Clay Springs AZ
Posts: 3,229
I ended up making a block a couple of times with different needle settings until the block came out exact.
Then I wrote the setting on my machine. No more problems, my machine is set at 2.3 for 1/4 inch.
You can do it with a simple strip set also.
Then I wrote the setting on my machine. No more problems, my machine is set at 2.3 for 1/4 inch.
You can do it with a simple strip set also.
#25
Junior Member
Join Date: Jan 2012
Posts: 108
I always watch the edge of the fabric ahead of the foot & try to keep that where it should be - that is what I was taught when Mom taught me to sew as a small child - so small I couldn't reach the treadle - she belted a box to the treadle for me to use - lol
#26
Super Member
Join Date: Dec 2011
Location: Horse Country, FL
Posts: 7,341
I found that using thinner bobbin thread helped with the "scant" quarter inch. Also, adjusting my needle so that it sewed the width of an index card line helped, as well. Good luck as you continue your quilting journey.
#27
Super Member
Join Date: Jul 2008
Location: Keller, TX
Posts: 1,942
I learned to concentrate on where my hand is in guiding that last inch from a Serger instructor. She pointed out that most of us unconsciously pull the fabric to the left, then running off the edge of the fabric. She told us to never put our hand beyond the needle on serging, so then I started watching my hand when coming to the end of my piecing on my sewing machine.....yep, I was pulling the piece slightly to the left. So I started using a stylus to hold my piece at the end so it did not veer off and was held close to the 1/4" marking. It works. Also, I don't sew a 1/4" any more, I use a scant 1/4, my piecing seems to go together better and I am not short fabric when squaring up the block....I would rather trim a block then not have enough and have to unsew lots of pieces.
#28
Super Member
Join Date: May 2012
Location: Central Wisconsin
Posts: 4,391
You can buy a stylus for a lot of money, use a chopstick from your Chinese meal, or use a bamboo skewer. The skewers are way too long, so I cut mine in half or less (my kitchen scissors will do that) and put them in the pencil sharpener. A very gentle push into the sharpener will get it as sharp as you like. I sharpen both ends this way. I have one with each machine and have given some away to others.
Happy sewing!
Last edited by maviskw; 01-06-2014 at 07:07 AM.
#30
Super Member
Join Date: Aug 2010
Location: Northern California, Sonoma Co.
Posts: 2,814
Yes, every machine is different as Rodney said.
I struggled with the 1/4 inch for years. I finally wrote down where I had to put the needle to get a 1/4 inch. Then I finally got better at my "art" and realized that it all wasn't me. My machine was finally sent back to the factory for and "overhaul." I got new feed dogs, new needle threader, you-name-it, I got it new. Can't tell you what a difference it made.
If you think you are crazy for not being able to get the 1/4 inch (and in my case a straight line; mine was straight but diagonal), consider that it just may be your machine.
I struggled with the 1/4 inch for years. I finally wrote down where I had to put the needle to get a 1/4 inch. Then I finally got better at my "art" and realized that it all wasn't me. My machine was finally sent back to the factory for and "overhaul." I got new feed dogs, new needle threader, you-name-it, I got it new. Can't tell you what a difference it made.
If you think you are crazy for not being able to get the 1/4 inch (and in my case a straight line; mine was straight but diagonal), consider that it just may be your machine.
Thread
Thread Starter
Forum
Replies
Last Post
Favorite Fabrics
Main
66
08-15-2009 11:41 AM
ProquiltLongarmARTQUILTER
Main
25
02-20-2008 07:09 AM