How to Piece Better
#1
Member
Thread Starter
Join Date: Jun 2014
Posts: 26
How to Piece Better
Although I've been quilting a number of years, and do a pretty good job, I still struggle whe?n I'm piecing! I'm very careful when piecing (use a guide, and the right needle, thread, etc.) but I still haven't achieved the level that I would like to achieve in accuracy. Do you have some suggestions for me? I think I am holding and feeding the pieces correctly, but sometimes they are off or don't fit as they should. I know it should look better and the block should fit better. I have measured my 1/4, etc. but still need improvement. what are your thoughts? What have you done to get precise results? Thanks for helping.
#2
Power Poster
Join Date: Dec 2010
Location: Michigan
Posts: 11,276
Cutting: Are you cutting accurately? Do you use the same brand of rulers for your project. Sometimes lining up your fabric on one side or the other of the mark on the ruler can make a difference. Don't cut too many layers at once.
Sewing: that pesky 1/4" is a misnomer. You don't measure the seam, you measure the resultant patch! Here's a good way to check:
http://www.quiltingboard.com/tutoria...ce-t89997.html
Also, your seam allowance is a moving target. If you change your thread weight or fabric type, you should recheck your seam and adjust if needed.
Make sure that you maintain your seam allowance at the start and end of each patch. It's easy to get off track at these 2 places.
Pressing: Make sure that you are not pressing a tiny crease in the seam, or stretching/distorting the block.
Square up your units as you make them, then square your blocks.
I'm sure others will have more suggestions.
Sewing: that pesky 1/4" is a misnomer. You don't measure the seam, you measure the resultant patch! Here's a good way to check:
http://www.quiltingboard.com/tutoria...ce-t89997.html
Also, your seam allowance is a moving target. If you change your thread weight or fabric type, you should recheck your seam and adjust if needed.
Make sure that you maintain your seam allowance at the start and end of each patch. It's easy to get off track at these 2 places.
Pressing: Make sure that you are not pressing a tiny crease in the seam, or stretching/distorting the block.
Square up your units as you make them, then square your blocks.
I'm sure others will have more suggestions.
#4
This is going to sound silly perhaps - but "relax" and change your focus. Example....i never have had trouble with bias edged blocks because i don't believe in bias edges.....they do not exist in my universe....and so i don't have any trouble with them. If you focus on the "problem" of your pieces not fitting - you tend to be more tense and "get" what you focus on. I'm not trying to be a wise gal here.....it's just a thought....
Alternating the direction of your seams when pressing to the side helps because you can "nest" the seams.
Also....i have more than once used the trick of a dot of Elmer's wash out school glue at important or difficult seam intersections.....it really helps keep those points/corners where they belong.
Alternating the direction of your seams when pressing to the side helps because you can "nest" the seams.
Also....i have more than once used the trick of a dot of Elmer's wash out school glue at important or difficult seam intersections.....it really helps keep those points/corners where they belong.
#6
Super Member
Join Date: Mar 2011
Location: Central NJ
Posts: 5,572
I agree that your cutting is more likely the culprit. I know I have those issues myself especially if I do cutting over various times. Such as - cut x number of pieces/fabrics on day 1; next pieces/fabs day 2; etc. Day 1 I may line up the fabric on this side of the line on the ruler; day 2 might but the other side of the line. Usually nothing a little stretching or squishing can't accommodate, but still... But I also agree with PenniF...relax. You should not make yourself crazy with perfection. Especially on 'normal' blocks. If you're doing a really fiddly/precise block, you may want to jump in to paper piecing. It can make those really pointy blocks work perfectly.
#7
Super Member
Join Date: Apr 2007
Location: Alturas, CA
Posts: 9,393
Starching would be my suggestion, here is how I starch. I starch every piece of fabric I'm going to work with, at least 2 hours ahead of the time, throw it in a plastic bag, and let it sit, then I'll take it out, either line dry or throw in the dryer for a few minutes, then iron, have never had a problem with the iron getting all gunky then, I do spray mist with water since I don't use the steam on my iron.
Thread
Thread Starter
Forum
Replies
Last Post
AngelinaMaria
Main
9
04-17-2012 08:55 AM
barnbum
Pictures
16
03-11-2008 07:30 AM