2-1/2" Strip Variation help..... (jelly rolls, balipops, etc.)
#37
I can see where this would work, but ONLY if the strips were cut straight.
I saw some posts about precut strips not even being cut straight. In those cases, one could not use this method or, one would be sewing crooked seams.
I saw some posts about precut strips not even being cut straight. In those cases, one could not use this method or, one would be sewing crooked seams.
#38
Power Poster
Join Date: May 2010
Location: Bakersfield, CA
Posts: 13,214
Originally Posted by countryone77
I can see where this would work, but ONLY if the strips were cut straight.
I saw some posts about precut strips not even being cut straight. In those cases, one could not use this method or, one would be sewing crooked seams.
I saw some posts about precut strips not even being cut straight. In those cases, one could not use this method or, one would be sewing crooked seams.
#39
Originally Posted by debbieumphress
Not all 2-1/2" strips are exactly 2-1/2". Ballipops are hand cut inBali so there is some variations there.
Here's something I found that assures us 2-1/2" strips when sewn.
When sewing two strips together, rather than measuring 1/4" to the right of the needle position, I measure 2-1/4" to the left of the needle. A piece of blue painter's tape is placed along the left edge of the 2-1/4".
A jelly roll fan-THANK YOU for this new approach! I will give it a whirl!
The fabric strips are positioned right sides together, paying close attention to keep the raw edges aligned at the left edge. As the strips are sewn together, care is taken to keep the left edges alligned with the tape strip. If there is any variation in strip width, it will fall within the seam allowance.
The sewn strip is pressed and the width measured. The seam allowance is narrow in some places and wider in others, but the finished width is consistently 4-1/2" wide. This method works to correct the strips used when 2 strips are sew together and then sub-cut.
When sewing two strips together using this manner, you will need to adjust the way you hold the strips and where you watch the trips as they are being fed through the sewing machine.
While it is not a cure-all, it does put your pieces will on the way to accuracy when the project begins with strip piecing.
It's so much easier than it sounds. Give it a try. Save on wasting strips.
Hope this helps everyone. Some patterns really rely on the strips being accurate or it throws off the whole block.
I read this originally in a book by Brenda Henning so please give her credit for this wonderful tute. Thank you.♥♥
Here's something I found that assures us 2-1/2" strips when sewn.
When sewing two strips together, rather than measuring 1/4" to the right of the needle position, I measure 2-1/4" to the left of the needle. A piece of blue painter's tape is placed along the left edge of the 2-1/4".
A jelly roll fan-THANK YOU for this new approach! I will give it a whirl!
The fabric strips are positioned right sides together, paying close attention to keep the raw edges aligned at the left edge. As the strips are sewn together, care is taken to keep the left edges alligned with the tape strip. If there is any variation in strip width, it will fall within the seam allowance.
The sewn strip is pressed and the width measured. The seam allowance is narrow in some places and wider in others, but the finished width is consistently 4-1/2" wide. This method works to correct the strips used when 2 strips are sew together and then sub-cut.
When sewing two strips together using this manner, you will need to adjust the way you hold the strips and where you watch the trips as they are being fed through the sewing machine.
While it is not a cure-all, it does put your pieces will on the way to accuracy when the project begins with strip piecing.
It's so much easier than it sounds. Give it a try. Save on wasting strips.
Hope this helps everyone. Some patterns really rely on the strips being accurate or it throws off the whole block.
I read this originally in a book by Brenda Henning so please give her credit for this wonderful tute. Thank you.♥♥
#40
Originally Posted by np3
Originally Posted by countryone77
I can see where this would work, but ONLY if the strips were cut straight.
I saw some posts about precut strips not even being cut straight. In those cases, one could not use this method or, one would be sewing crooked seams.
I saw some posts about precut strips not even being cut straight. In those cases, one could not use this method or, one would be sewing crooked seams.
If the left side is crooked (moves in and out), then my seam will also be crooked (move in and out). I don't see how that works.
If the left side is straight, but the width is incorrect, then it will work, as my seam will be straight.
The article says this is not a cure-all.
Thread
Thread Starter
Forum
Replies
Last Post
nanna-up-north
Main
32
09-02-2014 10:57 AM