turning sharp points on elongated triangles
#1
Member
Thread Starter
Join Date: Nov 2013
Location: Long Island, NY & Rocky Mount, VA
Posts: 5
turning sharp points on elongated triangles
I've been scouring the net looking for the best way to get sharp corners on elongated triangles like a jesters hat or the santa/wizards and birds seen on this blog: http://virginiarobertsonsblog.com/ ... the triangles I'm working with are 6" wide x 16" long, 5"W x 14L and 6"W x 12"L.. I've fooled with knitting needles, bodkins and this other long plastic thing that kinds holds the point while you turn.. but none are allowing me good sharp points.. Can anyone guide me please?
thanks!
thanks!
#2
Power Poster
Join Date: Mar 2011
Location: Ontario, Canada
Posts: 41,539
Are you sewing sharp points and and then turning them right side out? If so, you will need to trim the excess fabric from the points and grade the fabric going to the points on both sides so the point can be turned without too much fabric in the point. Be careful pushing out the points so you don't put a hole in the point.
It also helps to put the pointed end of your object (I use my Purple Thang)right up into the point before turning the whole piece. Hold the point and material with your fingers and then ease the rest of the triangle down.
It also helps to put the pointed end of your object (I use my Purple Thang)right up into the point before turning the whole piece. Hold the point and material with your fingers and then ease the rest of the triangle down.
#3
I agree with Tartan about trimming and grading fabric at the point. I was told once never to make a point sharp, but to take one short stitch across the tip. When doing collars and such, it did turn neater.
I also buy cheap wooden skewers for use as stilletos or turners. Just be sure to use something like sand paper to smooth any snags and you can cut them to length.
I also buy cheap wooden skewers for use as stilletos or turners. Just be sure to use something like sand paper to smooth any snags and you can cut them to length.
Last edited by nanacc; 09-13-2014 at 11:40 PM. Reason: add
#4
Super Member
Join Date: Oct 2011
Location: South Central Indiana
Posts: 1,931
All good tips so far, I also have used a stout pin or needle and inserted it into the seam near the tip to "poke" or "push" the point in place. You do have to be careful not to pull the fabric threads out when doing this as there is not much there after trimming and grading your seams.
#5
Super Member
Join Date: Mar 2011
Location: Central NJ
Posts: 5,572
I was taught to sew the side seam up to the area of the point - sew 2 stitches across the top - then back down the other side seam. After the trimming/grading that has already been mentioned, this should get you the sharpest point you are probably going to get.
#6
This has always worked for me.
#7
Super Member
Join Date: Nov 2010
Location: SoCal
Posts: 1,813
Take two or three pieces of thread double the length of the hat, tie a knot in the center. Sew the hat seam so that one end of the string is in the hat and the other end with the knot is on the outside end that is tapered. Sew the tip with the thread caught in the seam at the tip, using small stitches. You do not want the knot to slip through. Grade seam, but DO NOT cut thread. Holding onto thread string from inside hat, gently pull. It will turn the hat and pull the point at the same time. Trim thread and then pull the knotted thread out from the inside. Hope you understand what I am trying to say; I am better at showing than explaining in words.
#8
Member
Thread Starter
Join Date: Nov 2013
Location: Long Island, NY & Rocky Mount, VA
Posts: 5
Take two or three pieces of thread double the length of the hat, tie a knot in the center. Sew the hat seam so that one end of the string is in the hat and the other end with the knot is on the outside end that is tapered. Sew the tip with the thread caught in the seam at the tip, using small stitches. You do not want the knot to slip through. Grade seam, but DO NOT cut thread. Holding onto thread string from inside hat, gently pull. It will turn the hat and pull the point at the same time. Trim thread and then pull the knotted thread out from the inside. Hope you understand what I am trying to say; I am better at showing than explaining in words.
OK I will try this last suggestion.. I can still get the thread in there now with the knot and all and yes I completely understand your method! The next set of 15 I'll sew them with the 1 or 2 stitches across and see how that goes.. and yes I know I need to really trim the excess - I only sewed 1/4" seams but they do need to be trimmed before any turning no matter which method..
Thanks!!!
#9
Senior Member
Join Date: Mar 2011
Posts: 602
[QUOTE=wkdwich;6887514]I've been scouring the net looking for the best way to get sharp corners on elongated triangles like a jesters hat or the santa/wizards and birds seen on this blog: http://virginiarobertsonsblog.com/ ... the triangles I'm working with are 6" wide x 16" long, 5"W x 14L and 6"W x 12"L.. I've fooled with knitting needles, bodkins and this other long plastic thing that kinds holds the point while you turn.. but none are allowing me good sharp points.. Can anyone guide me please?
I was taught that when you're sewing a point, you should stitch up one side, turn your fabric slightly, take one stitch across, then turn and sew down the other side. The extra stitch allows for the bulk from both sides of whatever it is your sewing together. Trim your fabric, and you should have a nice sharp point. Good luck!
I was taught that when you're sewing a point, you should stitch up one side, turn your fabric slightly, take one stitch across, then turn and sew down the other side. The extra stitch allows for the bulk from both sides of whatever it is your sewing together. Trim your fabric, and you should have a nice sharp point. Good luck!
#10
Junior Member
Join Date: Mar 2012
Posts: 226
have you tried the trick with the soda straw? You stick the soda straw inside the item to be turned, use a blunt tipped item like a knitting needle, crochet hook, or chopstick to push the point into the soda straw & continue pushing till the item is turned. Works best with the larger straws. I've tried it and it does work. just an idea.
Sandee in Mo
Sandee in Mo
Thread
Thread Starter
Forum
Replies
Last Post