? about half square triangles
#1
Junior Member
Thread Starter
Join Date: Oct 2011
Posts: 276
? about half square triangles
I am scratching my head over hand sewing a simple triangle from a square. I understand the steps but my problem is the points are always to close to the edge. Shouldn't they be 1/4" away or a little more? Mine are so close that it is impossible joining the next block without cutting off the tip. It's driving me buggy.
Maybe I should read more on the oversized triangles but I get so frustrated my brain shuts off.
Thank you for all your help and suggestions.
Maybe I should read more on the oversized triangles but I get so frustrated my brain shuts off.
Thank you for all your help and suggestions.
#2
Power Poster
Join Date: Mar 2011
Location: Ontario, Canada
Posts: 41,538
The points should be 1/4 inch from the edge you are putting in the seam. I am not quite understanding what triangles you are doing. Is it Flying Geese triangles, 2 triangles sewn together to make a square or making 2 triangles pairs from a square?
#3
Super Member
Join Date: Jun 2011
Location: Michigan. . .FINALLY!!!!
Posts: 6,726
I know that the general rule is to cut your squares 7/8" of an inch larger than than the desired size. I always cut mine 1" larger and trim them down. Extra work? Yes! But I never lose a point that way! For trimming down, I went to a local glass shop and had squares of plexiglass cut for the size of my blocks - 4 1/2", 5 1/2", 6 1/2", etc. couple of bucks each. I measure them before I leave the shop to make sure they are square and the right dimensions. When I get home. I draw a diagonal line on one side. I then cover that side with Invisigrip to prevent the diagonal line from being rubbed off and prevents the square from shifting on my blocks. I lay the diagonal line on the ruler on the seam of the HST. I then trim them. It keeps my seam in the center and I'm not trimming a lot off each side of my block. I also use a rotating mat. Makes easy work of it but it can be tedious, depending on how many HST are in your project. The extra work is worth it to me if it means perfect points everytime!
#4
Junior Member
Thread Starter
Join Date: Oct 2011
Posts: 276
I am making 2 triangles from a square to make a new square.
#6
Super Member
Join Date: Oct 2010
Location: Prescott Valley, AZ
Posts: 1,329
You're probably trying to over-think them. I know I tend to do that. After you've sewn your triangles together and pressed them open, sew them to the next piece. Is this where you are losing your point? It's OK. The next seam will meet the seam you just sewed and a new perfect (or nearly) point will be formed.
#8
Junior Member
Thread Starter
Join Date: Oct 2011
Posts: 276
You're probably trying to over-think them. I know I tend to do that. After you've sewn your triangles together and pressed them open, sew them to the next piece. Is this where you are losing your point? It's OK. The next seam will meet the seam you just sewed and a new perfect (or nearly) point will be formed.
#9
Junior Member
Thread Starter
Join Date: Oct 2011
Posts: 276
Great idea...and you know it's something I would not have thought of. Something so simple but yet I wouldn't have come up with the idea. Thank you very much.
#10
Power Poster
Join Date: Dec 2010
Location: Michigan
Posts: 11,276
If you are making half square triangles (HST), then the seam goes right to the corner. When you trim them down, you put the 45 degree line of your ruler right on the seam, so you preserve the point.
Here is one of many you tube videos that shows making HSTs a bit larger, then trimming;
http://www.youtube.com/watch?v=OQq-5p8RCS8
Here is one of many you tube videos that shows making HSTs a bit larger, then trimming;
http://www.youtube.com/watch?v=OQq-5p8RCS8
Thread
Thread Starter
Forum
Replies
Last Post