Appli-Soft?
#1
Member
Thread Starter
Join Date: Jul 2011
Location: Florida
Posts: 70
Appli-Soft?
I just received my Sun Bonnet Sue and Over All Sam accuquilt die cuts and can't wait to get started on them... I really enjoy appliqueing but I'm not crazy about the 'stiffness' of it. I'm using Heat N Bond Ultrahold and was wondering if there is another alternative or does it soften up after washing OR is that 'just the way it is'? Any advice would be so helpful. Thank You.
#3
Power Poster
Join Date: Dec 2010
Location: Michigan
Posts: 11,276
Hmmm, the Ultrahold is designed for crafts and home dec, not quilting. I can see why you think it's too stiff! There are more appropriate products out there as Candace mentioned.
there is a special thread on this board for applique:
http://www.quiltingboard.com/main-f1...re-t64769.html
lots of info here.
there is a special thread on this board for applique:
http://www.quiltingboard.com/main-f1...re-t64769.html
lots of info here.
#4
There are much lighter weight types of bonding agents you can try. Ask at your local quilt shop. Another way to use it is to just cut out about a 1/2 inch wide strip of the heat and bond, instead of covering the whole image.
#5
Super Member
Join Date: Nov 2010
Location: Cadillac, MI
Posts: 6,487
Heat and Bond Ultrahold is not meant to be sewn through because it will gum up the needle. Heat and Bond Lite is sewable, but is still somewhat stiff. I purchased some unmarked fusible web from my LQS that was much softer so there are products out there. Even Wonder Under is softer than the Heat and Bond products.
#6
Super Member
Join Date: Feb 2011
Location: DC metro area
Posts: 1,286
I've used the steam and seam 2, it's a little on the stiff side but no where as bad as the h&b ultra-that stuff is for when you don't plan to sew it down, just iron on-isn't more for wall hangings that don't get much wear and tear?
#7
Super Member
Join Date: Sep 2011
Location: Southern Indiana
Posts: 5,052
I use Steam A Seam II and then do the buttonhole stitch by hand around my appliques. I have no problems with it being hard to needle. You can also use a feather weight fusible inter-facing. I get it at Joanns.
#8
Super Member
Join Date: Jan 2012
Location: Holmen, WI
Posts: 6,459
How do you like your new Accuquilt? I was just reading about them today. I'd like to get one but there are so many brands on the market that it confuses me (which isn't too hard to do... LOL!).
#10
Banned
Join Date: Dec 2009
Location: Enid, OK
Posts: 8,273
I just received my Sun Bonnet Sue and Over All Sam accuquilt die cuts and can't wait to get started on them... I really enjoy appliqueing but I'm not crazy about the 'stiffness' of it. I'm using Heat N Bond Ultrahold and was wondering if there is another alternative or does it soften up after washing OR is that 'just the way it is'? Any advice would be so helpful. Thank You.
heat n bond ultra is NOT for machine applique at all! It even says it will gum up your needles. You need heat n bond lite or the new featherlite that is even better! OR learn to cut the center out of you design before you fuse your fabric to it! That is the best way with large pieces like Sue and Sam have! You leave just a little fusible on the outer edges! OR since you are die cutting, just get stitch-witchery and cut it when you cut out your fabrics..no paper fusible to waste at all! That is what I use and have for years, makes it easier to just slip that webbing under the applique and fuse it down!
Thread
Thread Starter
Forum
Replies
Last Post