Gett'en out that " nasty old" smell
#1
I recently found 90 plus finished blocks in a covered plastic bin and the fabric to complete the remaining 40 blocks too. I was just thrilled when I found this treasure because the hand drawn plans were also in the bin. Now the challenge is, how do I get that old musty, mildew odor out of the fabric so I can work on them? The blocks are muslin and reproduction prints that are all light pastels. There are no signs of mildew, just that "old nasty" smell.
These blocks have very special meaning to me and my family so I would like to treat them with honor and respect but, whoo-hoo, they smell too musty to work with. Does any one have any suggestions? I sure would appreciate your help. I thank you in advance.
These blocks have very special meaning to me and my family so I would like to treat them with honor and respect but, whoo-hoo, they smell too musty to work with. Does any one have any suggestions? I sure would appreciate your help. I thank you in advance.
#5
I would hang them outside for a few hours and hopefully that will be enough so you can work on them.
The vinegar is a wonderful idea, removes many odors. But.... do you want to wash them before you assemble them???
The vinegar is a wonderful idea, removes many odors. But.... do you want to wash them before you assemble them???
#6
Super Member
Join Date: Nov 2010
Location: Florida
Posts: 1,611
Mariposa is right use vinegar. I use it in the wash cycle, too. You could even add a bit of baking soda. I do that when I buy new fabric. You don't have to agitate the fabric. Just soak, spin, rinse and spin. If you are concerned about the cut blocks, you might want to put them in a large laundry bag and wash them. Good luck. :)
#7
If the fabric in the blocks wasn't prewashed you could cause some big headaches for yourself. I would put a bar or three of unwrapped deodorant soap (Dial or Safeguard) in the bin with them for a week or two.
#8
Power Poster
Join Date: Dec 2008
Location: Western Wisconsin
Posts: 12,930
Charcoal absorbs bad odors. I would purchase a couple pair of the charcoal OdorEaters brand of shoe insoles and close them off together in a clean bin or closed garbage bag for a couple of weeks.
In my opinion, it is very risky to try to wash blocks (or an unquilted top) without first basting them to a foundation fabric. You can end up with a distorted mess, even if you hand wash.
You really need something that absorbs odor, not something that masks odor. My featherweight machine's case had a terrible musty smell in it. Tried a dryer sheet, tried soap -- everything seemed to just add a different odor. Fresh air and sunshine did not help enough either. The charcoal OdorEaters insoles finally did the job.
In my opinion, it is very risky to try to wash blocks (or an unquilted top) without first basting them to a foundation fabric. You can end up with a distorted mess, even if you hand wash.
You really need something that absorbs odor, not something that masks odor. My featherweight machine's case had a terrible musty smell in it. Tried a dryer sheet, tried soap -- everything seemed to just add a different odor. Fresh air and sunshine did not help enough either. The charcoal OdorEaters insoles finally did the job.
#9
Originally Posted by Prism99
My featherweight machine's case had a terrible musty smell in it. Tried a dryer sheet, tried soap -- everything seemed to just add a different odor. Fresh air and sunshine did not help enough either. The charcoal OdorEaters insoles finally did the job.
Like you, I've tried seemingly everything to rid my FW case's funky smell..
I will definitely try this!
#10
Super Member
Join Date: Jul 2010
Location: Glenmoore, PA
Posts: 7,941
Originally Posted by WMUTeach
I recently found 90 plus finished blocks in a covered plastic bin and the fabric to complete the remaining 40 blocks too. I was just thrilled when I found this treasure because the hand drawn plans were also in the bin. Now the challenge is, how do I get that old musty, mildew odor out of the fabric so I can work on them? The blocks are muslin and reproduction prints that are all light pastels. There are no signs of mildew, just that "old nasty" smell.
These blocks have very special meaning to me and my family so I would like to treat them with honor and respect but, whoo-hoo, they smell too musty to work with. Does any one have any suggestions? I sure would appreciate your help. I thank you in advance.
These blocks have very special meaning to me and my family so I would like to treat them with honor and respect but, whoo-hoo, they smell too musty to work with. Does any one have any suggestions? I sure would appreciate your help. I thank you in advance.
Thread
Thread Starter
Forum
Replies
Last Post