How do I keep my fabric from getting stuck?
#1
I am doing a ton of half square trianges with my Fons & Porter ruler. LOVE it by the way :)
But because I am chain piecing the ends I put in keep getting caught in the feed dogs. I do lift the foot first - and I don't even put in the side with the sharp point. I don't know what I could be doing wrong. It seems like it is almost better when I go faster but I don't have as much control that way . . any idea's?
But because I am chain piecing the ends I put in keep getting caught in the feed dogs. I do lift the foot first - and I don't even put in the side with the sharp point. I don't know what I could be doing wrong. It seems like it is almost better when I go faster but I don't have as much control that way . . any idea's?
#4
Super Member
Join Date: Feb 2011
Location: Where the deer & antilope play and the eagles soar
Posts: 1,540
I prefer to just do them as squares a bit larger then cut them apart on the center line and you will end up with 2 HQT. Or if you already have them cut you could lay them on a piece of tissue paper. It will keep the fabric from going down into the needle hole then it will tear right off when you are done. crafty_linda_b
#5
Power Poster
Join Date: Mar 2009
Posts: 15,639
When I sew HSTs, I use the oversized square and chain piece 1/4" off the center line. I alternate the side that goes under the foot. That way I avoid having to deal with the pointy bit.
WIth this ruler, you will always have the point going through and one solution is to get a different needle plate for your machine (assuming it is offered). The single hole will not allow the fabric to be pulled into the feed dogs. HOWEVER you have to be aware that you can't switch to a different stitch - it will bust the needle.
WIth this ruler, you will always have the point going through and one solution is to get a different needle plate for your machine (assuming it is offered). The single hole will not allow the fabric to be pulled into the feed dogs. HOWEVER you have to be aware that you can't switch to a different stitch - it will bust the needle.
#7
Super Member
Join Date: Feb 2011
Location: DC metro area
Posts: 1,286
I have the exact same problem with triangles. Someone told me to change to a new needle. I haven't tried it yet so don't know if it helps.
How funny. looks like gaigai and I posted at the same time. saying the same thing- Jinx.
:lol:
How funny. looks like gaigai and I posted at the same time. saying the same thing- Jinx.
:lol:
#8
Senior Member
Join Date: Dec 2010
Location: West Virginia
Posts: 988
Use the scrap of fabric at the beginning of the chain. Place the needle in the middle of that fabric and sew to the edge. Have your piece ready to be picked up within the next couple of stitches. This way the feed dogs are still feeding the scrap all the way to the back while picking up the new fabric to start. I too was frustrated by this on my machine. I didn't have a single hole plate, just a zig-zag hole. It does eat up the fabric. When you're done with that chain, snip the scrap off and use it to start the next one. You can use it until it is completely full of threads. It's good to have a couple of these handy because they can seem to get away from you.
#9
Super Member
Join Date: Jun 2008
Location: Utah
Posts: 8,847
Originally Posted by cminor
I am doing a ton of half square trianges with my Fons & Porter ruler. LOVE it by the way :)
But because I am chain piecing the ends I put in keep getting caught in the feed dogs. I do lift the foot first - and I don't even put in the side with the sharp point. I don't know what I could be doing wrong. It seems like it is almost better when I go faster but I don't have as much control that way . . any idea's?
But because I am chain piecing the ends I put in keep getting caught in the feed dogs. I do lift the foot first - and I don't even put in the side with the sharp point. I don't know what I could be doing wrong. It seems like it is almost better when I go faster but I don't have as much control that way . . any idea's?
#10
Super Member
Join Date: Apr 2007
Location: North Carolina - But otherwise, NOTW
Posts: 7,940
Originally Posted by quiltsRfun
Originally Posted by cminor
I am doing a ton of half square trianges with my Fons & Porter ruler. LOVE it by the way :)
But because I am chain piecing the ends I put in keep getting caught in the feed dogs. I do lift the foot first - and I don't even put in the side with the sharp point. I don't know what I could be doing wrong. It seems like it is almost better when I go faster but I don't have as much control that way . . any idea's?
But because I am chain piecing the ends I put in keep getting caught in the feed dogs. I do lift the foot first - and I don't even put in the side with the sharp point. I don't know what I could be doing wrong. It seems like it is almost better when I go faster but I don't have as much control that way . . any idea's?
Thread
Thread Starter
Forum
Replies
Last Post
Sunflowerzz
For Vintage & Antique Machine Enthusiasts
23
10-21-2013 06:09 PM