Largest Quilt you have Quilted?
#1
Junior Member
Thread Starter
Join Date: Dec 2013
Location: Minnesota
Posts: 166
Largest Quilt you have Quilted?
I have a Janome 6600 and am currently FMQ a twin to full size quilt.
My next quilt is closer to a queen size.
I think I am going to quilt this one myself. I am a little worried about the size.
Would you tackle this? What is the largest quilt you have quilted on a DSM?
kitty
My next quilt is closer to a queen size.
I think I am going to quilt this one myself. I am a little worried about the size.
Would you tackle this? What is the largest quilt you have quilted on a DSM?
kitty
#2
Power Poster
Join Date: Dec 2010
Location: Michigan
Posts: 11,276
I would look at quilting as you go, or quilting in sections. There's a good book by Marti Michell which gives many different techniques on doing this:
http://www.amazon.com/Marti-Michell-...=marti+michell
http://www.amazon.com/Marti-Michell-...=marti+michell
#3
Senior Member
Join Date: May 2012
Location: Traverse City, MI
Posts: 405
I did a queen sized but only straight lines. The other queen sized I did the Gracie with a bl quilters pro which I have taken down. Next one will be quilt as you go method. I worked with a quilter that always used this method and her quilts were gorgeous! I did a full sized one several years ago that turned out well.
#6
Moderator
Join Date: Jun 2008
Location: Camarillo, California
Posts: 35,242
[ATTACH=CONFIG]487137[/ATTACH][ATTACH=CONFIG]487138[/ATTACH][ATTACH=CONFIG]487139[/ATTACH][ATTACH=CONFIG]487140[/ATTACH]This past winter/spring I quilted a large queen almost king size on my DSM Bernina. It is approx 101 x 111. I did a FMQ Flower and leaf design all over the quilt. It actually went much better than I had expected. It took 11 bobbins and I worked on it over 3 days.
I have a desk that my machine sinks into and the back lifts up to give me a larger flat surface. I also put wood clamps and cardboard around the edges to keep the quilt from falling off. I just made a big "puddle" and worked in that.
I have a desk that my machine sinks into and the back lifts up to give me a larger flat surface. I also put wood clamps and cardboard around the edges to keep the quilt from falling off. I just made a big "puddle" and worked in that.
__________________
My newest Grandson, Caleb Austin, was born May 29th. I am now Grandma to 4 precious babies. I am so blessed!!!!
My newest Grandson, Caleb Austin, was born May 29th. I am now Grandma to 4 precious babies. I am so blessed!!!!
Last edited by Jim's Gem; 08-11-2014 at 08:33 AM. Reason: added pictures
#7
Super Member
Join Date: Feb 2014
Location: Wis
Posts: 5,928
I made one about 102x90 on my littler Bernina. I did mostly swirlies and swooped around the flying geese. Just baste well and start in the middle. I usually end up having to re-smooth and re-pin as I work my way out. No matter how well I pin, there seems to be puffiness that needs to be re-smoothed towards the edges.
#9
Senior Member
Join Date: Mar 2012
Location: Kauai, Hawaii
Posts: 376
Think about when you are driving on the freeway -- you are "looking ahead" but really concerned about the vehicles in your immediate area - same with quilting. Getting your quilt "stable on the table" is the main concern -- then just do it in sections as noted above - center out. Did a full on my back up machine - less than 6" throat. Must admit it's much easier with a wide throat area.
#10
Once I quilted an oversized king quilt on my Bernina because I could not find a LAQ who would do a quilt that large. I cut the batting into 3 sections and the quilting went well. I used SITD for the quilt top and FMQ on the wide borders. I still do some twin size quilts on my Bernina; but recently, I have been sending large quilts to the LAQ. Best wishes with your queen size quilt.
Thread
Thread Starter
Forum
Replies
Last Post
LadyAg
Main
8
10-05-2019 05:59 AM
zozee
For Vintage & Antique Machine Enthusiasts
28
10-30-2013 01:42 PM