Why are my 1 inch strips bowing after being sewn? They are smiling at me.
#1
Senior Member
Thread Starter
Join Date: Aug 2011
Location: The California Hills
Posts: 626
Why are my 1 inch strips bowing after being sewn? They are smiling at me.
I am sewing a large number of 10 inch long by 1 inch wide 2 and 3 strip sets. The background strip is a regular cotton and the other strips are Hoffman batiks. When I sew 2 strips together, they come out of the sewing machine slightly bowed. The center spot is bowed down (so it looks like a smile when placed on the cutting board the same side up and was sewn) by 1/8 of an inch. I am wonder if there is something I should be doing or changing that would prevent that.
I am using a new sharp 70/10 needle that was recommended to me for use with my batiks.
I am using Connecting Threads thread which is 50 weight.
Is there something that will stop this from happening or do you just need to correct it by straightening out the piece gently when you set it to press?
I am using a new sharp 70/10 needle that was recommended to me for use with my batiks.
I am using Connecting Threads thread which is 50 weight.
Is there something that will stop this from happening or do you just need to correct it by straightening out the piece gently when you set it to press?
#2
Super Member
Join Date: Feb 2011
Location: DC metro area
Posts: 1,286
Can you post some photos? That may help show what you are talking about.
I've had problems with bowing when I sew several strips together until I learned to sew from alternating sides/ends of the strip sets. But since you are only sewing 2 strips, that shouldn't be the problem.
I've had problems with bowing when I sew several strips together until I learned to sew from alternating sides/ends of the strip sets. But since you are only sewing 2 strips, that shouldn't be the problem.
#3
Sounds wired but did you lay a strip out to see if it's cut perfectly straight. I usually lay a strip down on the counting mat and make sure it's all straight....were human it happens!! Ask me how I know!
#5
It could be one of two things and it always drives me nuts. If the balance of the tension is off, then over the course of several inches there is less bobbin thread being used than top thread, so the straight line of your edges becomes curved. What I usually do is to lay the strip on my table and then run my fingernail along the seam to pull more bobbin thread through the length of the seam; it seems to help. Also, if your strips are not cut exactly on the straight of grain it can result in the bowing. You're not alone.
#7
Senior Member
Thread Starter
Join Date: Aug 2011
Location: The California Hills
Posts: 626
Can I just correct this by gently curving them back into a straight line before pressing? I have tried increasing and decreasing tension and they still came out the same. I tried feeding them batik on top for some and the other fabric on top for the others and they all stilled bowed slightly the same. All my strips are within a hair of 1 inch and do lay out straight on the cutting matt before sewing.
#8
Super Member
Join Date: May 2011
Location: Pacific NW
Posts: 9,585
You might be able to press them straight. Make sure you're not pulling the strip as you're sewing - I've done that. If you have a walking foot, you might try that to see if it helps prevent the bowing.
Also, if you're sewing more than 2 strips together, alternate the ends where you start. In other words, when you sew strip A to strip B, start at the north end, then when you sew strip C, start at the south end.
Also, if you're sewing more than 2 strips together, alternate the ends where you start. In other words, when you sew strip A to strip B, start at the north end, then when you sew strip C, start at the south end.
#9
I would add:
- is your material not on the straight of grain, but biased a bit?
- are you using a seam guide or a flanged foot?
- are you using any starch or Best Press sort of thing, which helps prevent this.
I love my Pfaff because of the IDT -integrated dual technology. It is like have 2 sets of feed dogs, top and bottom, so I don't stretch my fabric when I sew.
ali
- is your material not on the straight of grain, but biased a bit?
- are you using a seam guide or a flanged foot?
- are you using any starch or Best Press sort of thing, which helps prevent this.
I love my Pfaff because of the IDT -integrated dual technology. It is like have 2 sets of feed dogs, top and bottom, so I don't stretch my fabric when I sew.
ali
#10
Senior Member
Join Date: Jun 2011
Posts: 965
I find that batiks have such a tighter weave than your standard cotton that perhaps having one "stretchier" than the other is causing a problem. Not usually when you are sewing simple squares together, but long strips maybe....
Although I like the look of batiks, I find working with it to be unforgiving because there is no give.
Carole
Although I like the look of batiks, I find working with it to be unforgiving because there is no give.
Carole
Thread
Thread Starter
Forum
Replies
Last Post
craftybear
Links and Resources
1
08-10-2011 12:37 PM