Can you tell me what this is?....Please
#1
Senior Member
Thread Starter
Join Date: Nov 2010
Location: Upstate NY
Posts: 724
Can you tell me what this is?....Please
I purchased this sewing machine over the summer, just got it out to try it out, well don't ya know, the thing I thought was a foot pedal looks like it has heating coils in it and sits on its side (?) I am hoping I can get the pics to load. I am wondering if anyone knows what this could be.
#3
Super Member
Join Date: Feb 2012
Posts: 8,091
Yes that is the foot controller. Some of the older ones were made like that. There will be a part that moves and some feet that will tell you which way to set it on the floor.
The older ones worked by resistance. When the pedal was all the way up there was no connection, as you pushed the pedal or lever down the resistance went from high which gave you low speed, to low or none which gave you high speed.
So that is your throttle.
Joe
The older ones worked by resistance. When the pedal was all the way up there was no connection, as you pushed the pedal or lever down the resistance went from high which gave you low speed, to low or none which gave you high speed.
So that is your throttle.
Joe
#6
Senior Member
Thread Starter
Join Date: Nov 2010
Location: Upstate NY
Posts: 724
Yes that is the foot controller. Some of the older ones were made like that. There will be a part that moves and some feet that will tell you which way to set it on the floor.
The older ones worked by resistance. When the pedal was all the way up there was no connection, as you pushed the pedal or lever down the resistance went from high which gave you low speed, to low or none which gave you high speed.
So that is your throttle.
Joe
The older ones worked by resistance. When the pedal was all the way up there was no connection, as you pushed the pedal or lever down the resistance went from high which gave you low speed, to low or none which gave you high speed.
So that is your throttle.
Joe
Do you have an idea why there would be coils inside the black pedal?
#7
Super Member
Join Date: Nov 2010
Location: Cadillac, MI
Posts: 6,487
I have one, too, but I think it's history. The last time it was used, it stopped working and smelled like burned plastic. The machine is much prettier than this pic. I scraped off that r/w/b emblem, but it still needs cleaning. The faceplate and the turquoise trim are an Art Deco pattern. [ATTACH=CONFIG]318991[/ATTACH][ATTACH=CONFIG]318992[/ATTACH]
#8
Super Member
Join Date: Feb 2012
Posts: 8,091
My Kenmore has the same foot controller. You put it on the floor with the feed down and the large vented part upright. Then push up and down on the lever on the side. Works just fine.
Joe
#9
Super Member
Join Date: Feb 2012
Posts: 8,091
irishrose,
Don't condemn your foot controller yet. As I look at your pictures I see some swelling and deterioration of the cord. The old foot controllers can be taken apart and rewired. Sometimes the cord ends are soldered, but usually they are attached with screws or nuts.
The old cords used in the 40s and 50s and probably earlier is insulated with latex rubber. It is prone to turning soft and chemically deteriorating. So check your wiring first.
I just rewired a Singer 66-18 that had cord so bad it looked as if the insulation was burned. But it was just rotted from age and use.
Also A LOT of electrical cord I've seen on these old machines contains aluminum wire. This was good when new, but with age and use it deteriorates as well. I replace it as fast as I can.
Joe
Don't condemn your foot controller yet. As I look at your pictures I see some swelling and deterioration of the cord. The old foot controllers can be taken apart and rewired. Sometimes the cord ends are soldered, but usually they are attached with screws or nuts.
The old cords used in the 40s and 50s and probably earlier is insulated with latex rubber. It is prone to turning soft and chemically deteriorating. So check your wiring first.
I just rewired a Singer 66-18 that had cord so bad it looked as if the insulation was burned. But it was just rotted from age and use.
Also A LOT of electrical cord I've seen on these old machines contains aluminum wire. This was good when new, but with age and use it deteriorates as well. I replace it as fast as I can.
Joe
Thread
Thread Starter
Forum
Replies
Last Post
AngelinaMaria
Main
6
05-20-2014 11:05 PM
Chester the bunny
Main
9
03-10-2014 05:28 AM
AngelinaMaria
Main
12
09-20-2013 03:50 PM
nygal
For Vintage & Antique Machine Enthusiasts
19
09-15-2012 12:12 PM
Willa
Main
31
11-03-2011 01:31 PM