Featherweight Problem
#1
Member
Thread Starter
Join Date: Nov 2012
Location: Maryland
Posts: 3
Featherweight Problem
I have two featherweights, a beautiful black one and a pretty white one. I am having an issue with the white one. I can make a bobbin just fine, but when I turn the stop button back the needle will not move, and I can barely make it move by turning the wheel manually. I unscrewed the stop wheelandtook it off. i am not sure if i put it back together correctly, and cannot find any references on to assemble it. Does anyone have any wisdom to help me figure out what is wrong.
any help will be greatly appreciated.
Ellie
any help will be greatly appreciated.
Ellie
#2
Hi Ellie,
A couple of things worth looking at.
Ok,.. the stop motion "washer", under that big knob, should have the flared part, the inside "teeth" sticking toward the wheel side.
In theory, I guess the washer being out of place could cause problems with turning the wheel, but I suspect that the problem lies under the bobbin case.
When I got my latest FW, it had a similar problem. The needle would move a little, the hand wheel would turn about an inch either way, but that was it. I had what was close to 10ft of thread caught behind the bobbin case. I could see some of it without dis-assembly, but when I got it apart it was staggering!
This is a write up done by someone else that should show you how to clear it. The threads can be difficult to see, so look very carefully. It's also a great opportunity to dust in there.
http://thefeatherweight221factory.co...MachineJam.php
Good luck! Let us know if it works, or you have further questions.
A couple of things worth looking at.
Ok,.. the stop motion "washer", under that big knob, should have the flared part, the inside "teeth" sticking toward the wheel side.
In theory, I guess the washer being out of place could cause problems with turning the wheel, but I suspect that the problem lies under the bobbin case.
When I got my latest FW, it had a similar problem. The needle would move a little, the hand wheel would turn about an inch either way, but that was it. I had what was close to 10ft of thread caught behind the bobbin case. I could see some of it without dis-assembly, but when I got it apart it was staggering!
This is a write up done by someone else that should show you how to clear it. The threads can be difficult to see, so look very carefully. It's also a great opportunity to dust in there.
http://thefeatherweight221factory.co...MachineJam.php
Good luck! Let us know if it works, or you have further questions.
#3
Member
Thread Starter
Join Date: Nov 2012
Location: Maryland
Posts: 3
Made some progress
Thanks for the reply. I took the throat plate off and examined the bobbin area and found no thread jams. I took stop motion knob off again and positioned the flanged eges of the washer facing to the right of the machine (not sure if this is what you meant). I am able to turn wheel with my hand now (although it is nowhere near as smooth with my other featherweight), and I am now thinking the problem is with the belt and/or the position of the motor. I've ordered a new belt so I will wait until it arrives before fiddling any further.
Hi Ellie,
A couple of things worth looking at.
Ok,.. the stop motion "washer", under that big knob, should have the flared part, the inside "teeth" sticking toward the wheel side.
In theory, I guess the washer being out of place could cause problems with turning the wheel, but I suspect that the problem lies under the bobbin case.
When I got my latest FW, it had a similar problem. The needle would move a little, the hand wheel would turn about an inch either way, but that was it. I had what was close to 10ft of thread caught behind the bobbin case. I could see some of it without dis-assembly, but when I got it apart it was staggering!
This is a write up done by someone else that should show you how to clear it. The threads can be difficult to see, so look very carefully. It's also a great opportunity to dust in there.
http://thefeatherweight221factory.co...MachineJam.php
Good luck! Let us know if it works, or you have further questions.
A couple of things worth looking at.
Ok,.. the stop motion "washer", under that big knob, should have the flared part, the inside "teeth" sticking toward the wheel side.
In theory, I guess the washer being out of place could cause problems with turning the wheel, but I suspect that the problem lies under the bobbin case.
When I got my latest FW, it had a similar problem. The needle would move a little, the hand wheel would turn about an inch either way, but that was it. I had what was close to 10ft of thread caught behind the bobbin case. I could see some of it without dis-assembly, but when I got it apart it was staggering!
This is a write up done by someone else that should show you how to clear it. The threads can be difficult to see, so look very carefully. It's also a great opportunity to dust in there.
http://thefeatherweight221factory.co...MachineJam.php
Good luck! Let us know if it works, or you have further questions.
#4
Hey Ellie,
How does the machine turn if you take the belt off? That should help you rule out the belt and motor...
Also, when's the last time the machine was completely oiled?
Did you disassemble the way the link shows? Or just take the throat plate off?
Yes, that's exactly what I meant when I described the stop motion washer. Sorry if it wasn't clear.
How does the machine turn if you take the belt off? That should help you rule out the belt and motor...
Also, when's the last time the machine was completely oiled?
Did you disassemble the way the link shows? Or just take the throat plate off?
Yes, that's exactly what I meant when I described the stop motion washer. Sorry if it wasn't clear.
#5
Super Member
Join Date: Feb 2012
Posts: 8,091
More than likely the belt and motor has nothing to do with it. As ArchaicArcane said, remove the belt and try it then.
You might not be able to see it, but there still could be a piece of thread behind the bobbin assembly. That was the case with our FW when we got it. Locked up tight. I had to take the bobbin assembly apart to clear it. Made all the difference in the world.
Then oil it. If it's stiff and rough it could just need oil. And grease.
Joe
You might not be able to see it, but there still could be a piece of thread behind the bobbin assembly. That was the case with our FW when we got it. Locked up tight. I had to take the bobbin assembly apart to clear it. Made all the difference in the world.
Then oil it. If it's stiff and rough it could just need oil. And grease.
Joe
#6
Member
Thread Starter
Join Date: Nov 2012
Location: Maryland
Posts: 3
Thanks for all the replies. I did a good cleaning and then oiled it. Now it is running smoothly. I guess one can never underestimate the maintenance process. I found a really good tutorial here for oiling. It was much more helpful than the manuals.
Ellie
Ellie
Thread
Thread Starter
Forum
Replies
Last Post
ruby2shoes
Main
25
09-20-2015 04:01 PM
BETTY62
For Vintage & Antique Machine Enthusiasts
4
10-12-2012 09:47 AM
corgiplace
For Vintage & Antique Machine Enthusiasts
8
08-29-2011 05:01 PM