Mud Dauber Nests Inside VSM Head
#1
Member
Thread Starter
Join Date: Apr 2013
Location: Oklahoma
Posts: 58
Mud Dauber Nests Inside VSM Head
Months ago, my sister gave me a Simmons Velox treadle machine and table she had found inside their newly acquired rental home. I am getting around to cleaning it up now, but there appears to be some old mud dauber nests up inside the head. What is the safest way to clean those out without harm to the machine and mechanics inside? TIA!
#2
Are they still inhabited? If not perhaps a long screwdriver and a vacuum to get them out. If the occupants are still there, place the machine head in a plastic trash bag with some wasp killer sprayed on the bottom of the bag and seal it for a couple of days. Then use the screwdriver and vacuum. Use rubber gloves to clean if you went the bug spray route.
#3
Member
Thread Starter
Join Date: Apr 2013
Location: Oklahoma
Posts: 58
No, no, no...They are loooooooooooooooooooong gone. Goodness me...I would freak out if they were still in there!!
I'll try to the screwdriver and vacuum method. Is there anything that could be safely sprayed or applied up inside that wouldn't harm the mechanics? I'm sure there will be dirt residue left.
I'll try to the screwdriver and vacuum method. Is there anything that could be safely sprayed or applied up inside that wouldn't harm the mechanics? I'm sure there will be dirt residue left.
Are they still inhabited? If not perhaps a long screwdriver and a vacuum to get them out. If the occupants are still there, place the machine head in a plastic trash bag with some wasp killer sprayed on the bottom of the bag and seal it for a couple of days. Then use the screwdriver and vacuum. Use rubber gloves to clean if you went the bug spray route.
#4
Not sure about anything that could be sprayed up there. My thinking anything like WD-40 or Bose Shield would leave a residue or just allow the remaining dirt to go onto the gears. A well lit area would be helpful. You could ry making a long q-tip with a chop stick and a cotton ball taped on the end with a solvent to clean the dusty remains up.
#5
Super Member
Join Date: Mar 2016
Posts: 2,891
It almost seems to me like you're going to have to wash them out with something. Those nests are really stuck in most cases. If you just poke up in there with something and vacuum, you're going to leave a lot of dirt still stuck in there. If you use water, then you have to be vigilant on getting the all water out and preventing rust. I wonder if kerosene would dissolve the nests? It would take a lot of kerosene to wash it repeatedly, which it will probably require.
Hmmmm....Good question.
Maybe someone else has a good idea.
bkay
Hmmmm....Good question.
Maybe someone else has a good idea.
bkay
#6
I just wanted to say that the nests you see might just be the tip of the iceberg. I saw nests under the pillar of one of my machines. I took an ice pick to it. Worked a long time. pulled off the inspection late at the top of the pillar and I couldn't see any machine parts, just dried mud. Taking the faceplate off gave me the same view. I haven't resorted to soaking yet, but I am about ready to give it a bath in used motor oil since I have some kicking around. I can finally get rotating parts moving, but not with any free spinning. I used the ice pick, a long skinny screwdriver and a punch. Chop sticks would have just splintered in my challenge. best wishes.
#9
You might check out Vintage Sewing Machine Shop.....Come on in and sit a spell
purplefiend had a small one in the back of her 115 and Bennett evidently has had experience in that respect. I was thinking a metal spiral brush, but I don't think I've seen any in a size that would do any good. The metal brushes I have probably wouldn't get very far in the pillar. Bennett's suggestion was a bottle brush.
We like pictures. Good luck. Sounds like a neat machine worth saving.
Janey - Neat people never make the exciting discoveries I do.
purplefiend had a small one in the back of her 115 and Bennett evidently has had experience in that respect. I was thinking a metal spiral brush, but I don't think I've seen any in a size that would do any good. The metal brushes I have probably wouldn't get very far in the pillar. Bennett's suggestion was a bottle brush.
We like pictures. Good luck. Sounds like a neat machine worth saving.
Janey - Neat people never make the exciting discoveries I do.
#10
Member
Thread Starter
Join Date: Apr 2013
Location: Oklahoma
Posts: 58
Thread
Thread Starter
Forum
Replies
Last Post
cizzors
General Chit-Chat (non-quilting talk)
70
10-23-2011 06:59 AM