Is it possible to 'spot' shellac?
#1
Is it possible to 'spot' shellac?
I have a 42 cabinet that's in nice shape over all, although the veneer is lifted on the bottom in one place. I read to use an old credit card to push in glue, then clamp, so I think that's okay.
The bigger problem, I think, is a ring on the top where the finish is completely gone. I wondered whether Glenn's technique with denatured alcohol and shellac would work on just that spot? Could I kind of feather in from the areas that are okay? Or is there another way to restore the shine to that spot without redoing the whole top?
Thank you![ATTACH=CONFIG]499321[/ATTACH]
The bigger problem, I think, is a ring on the top where the finish is completely gone. I wondered whether Glenn's technique with denatured alcohol and shellac would work on just that spot? Could I kind of feather in from the areas that are okay? Or is there another way to restore the shine to that spot without redoing the whole top?
Thank you![ATTACH=CONFIG]499321[/ATTACH]
#3
Super Member
Join Date: Mar 2010
Location: Huntsville, AL
Posts: 2,609
Yes you can spot shellac. First start out with a little shellac with a drop or two of linseed oil and french polish the area. Keep doing this many times until the area is level with the rest then French polish to blend in. You may want to use the amber shellac first to darken the water ring then use clear to finish the repair. You can also use a fine artist brush and brush the shellac on in thin coats until it is level with the rest of the finish. Waiting about an hour between coats, should only take about three thin coats. Then You can french polish the area smooth. After a week of curing wax the entire cabinet with a good quality past wax. I use Bri wax.
Skip
Skip
#4
#6
#7
Junior Member
Join Date: Nov 2010
Location: Harrisonburg, VA
Posts: 167
#8
Super Member
Join Date: Mar 2010
Location: Huntsville, AL
Posts: 2,609
Bruce cabinet and machine I cleaned up
The cabinet was cleaned and then french polished then waxed with Bri wax and very fine steel wool. the bad areas were spot shellaced then went over the entire cabinet with french polish and waxed. The machine was so dirty I could not see the decals so cleaned and french polished it also. This one was done about two years ago. Sews great. I have about 6 more that I have done this way.
Skip
Skip
Last edited by Glenn; 11-19-2014 at 10:38 AM. Reason: Add info
#9
Wow, Glenn, that is breathtaking!
Do you have a preference between applying the shellac to the spot with an artist brush and then french polishing or doing only french polishing? I'd like to just try the artist brush approach first, because I think it will be easier to tell what I'm doing.
Do you use canned shellac or dissolve flakes? (The flakes I've found are really expensive.)
Do you have a preference between applying the shellac to the spot with an artist brush and then french polishing or doing only french polishing? I'd like to just try the artist brush approach first, because I think it will be easier to tell what I'm doing.
Do you use canned shellac or dissolve flakes? (The flakes I've found are really expensive.)
#10
Super Member
Join Date: Mar 2010
Location: Huntsville, AL
Posts: 2,609
Linda, I use both the flakes and canned shellac. It is perfectly fine to use the shellac in qt cans you get at Lowes or Home Depot. It is about $13 a can here but will last you thru several cabinets. Flakes can get pricey but they are better than the canned because you can mix up what you need. I have had excellent results with the canned so go for that. When I had my restoration shop I would use only the flakes but now retired I use the canned it is easier.
Skip
Skip
Thread
Thread Starter
Forum
Replies
Last Post
Glenn
For Vintage & Antique Machine Enthusiasts
718
07-07-2024 05:15 AM
Glenn
For Vintage & Antique Machine Enthusiasts
105
06-17-2023 07:05 AM
bearisgray
Main
16
11-26-2019 08:05 PM
Glenn
For Vintage & Antique Machine Enthusiasts
35
07-03-2014 08:44 PM
Cecilia S.
For Vintage & Antique Machine Enthusiasts
2
01-03-2014 12:39 PM