Can I ask for help from some of our Featherweight restorers?
#1
Super Member
Thread Starter
Join Date: Feb 2011
Location: Rhode Island
Posts: 1,663
Can I ask for help from some of our Featherweight restorers?
I'm sorry to be bugging you all again, but I'm still trying to work my way around the Featherweight I bought from a friend. I've posted before about the smelly issue so I won't get into that again. Now I have another question about something else, so I hope you'll indulge me.
I'll start with something positive (because I feel like all I've done for the past month is complain about this machine!) it certainly does make a perfect stitch. However, 99% of the time when I press on the pedal - it came with a grey pedal, which I read on another internet resource is an actual vintage pedal - the machine will not "go". I have to turn the hand wheel to get it to actually run. I have oiled the machine several times already but that doesn't seem to be the problem. I'm wondering if there's something actually wrong with the pedal or with the machine's wiring.
In oiling her today, I was looking underneath at the wiring, which again I was told (on another Featherweight group) not to touch or clean because it's coated in lead. I noticed that there seem to be some frayed spots, but since I'm not mechanically-included at all, I don't know if this is what they are supposed to look like, or if there's a problem. I have attached some photos of the underside of my machine - can anyone can tell me if they see anything that looks odd or off? (The second picture shows the spot where I think it looks really frayed, with three little pieces sticking out.)
At this point I am just really frustrated. I may have bought the machine inexpensively (it was $250) but I feel as though I'm going to end up spending more money just to feel comfortable using it... I should have spent more money at the outset and bought from someone who really was a restorer. I don't know if I should buy a new pedal, which would cost at least $50, or just bring it to a qualified repair person who can take a look at it.
Okay, I'm done whining for today. Any help is appreciated.
I'll start with something positive (because I feel like all I've done for the past month is complain about this machine!) it certainly does make a perfect stitch. However, 99% of the time when I press on the pedal - it came with a grey pedal, which I read on another internet resource is an actual vintage pedal - the machine will not "go". I have to turn the hand wheel to get it to actually run. I have oiled the machine several times already but that doesn't seem to be the problem. I'm wondering if there's something actually wrong with the pedal or with the machine's wiring.
In oiling her today, I was looking underneath at the wiring, which again I was told (on another Featherweight group) not to touch or clean because it's coated in lead. I noticed that there seem to be some frayed spots, but since I'm not mechanically-included at all, I don't know if this is what they are supposed to look like, or if there's a problem. I have attached some photos of the underside of my machine - can anyone can tell me if they see anything that looks odd or off? (The second picture shows the spot where I think it looks really frayed, with three little pieces sticking out.)
At this point I am just really frustrated. I may have bought the machine inexpensively (it was $250) but I feel as though I'm going to end up spending more money just to feel comfortable using it... I should have spent more money at the outset and bought from someone who really was a restorer. I don't know if I should buy a new pedal, which would cost at least $50, or just bring it to a qualified repair person who can take a look at it.
Okay, I'm done whining for today. Any help is appreciated.
#3
Super Member
Thread Starter
Join Date: Feb 2011
Location: Rhode Island
Posts: 1,663
I do have the Sebro book; I will recheck it for any info on wiring. I haven't bought the DVDs by Dave McCallum because they are pretty pricey. I'm not sure whether to spend that $$$ on the DVDs or a repair person!!
#4
Super Member
Join Date: Feb 2012
Posts: 8,091
DonnaC,
I had that exact same thing happen with a 201. Sews fine, stop to do something, push on the controller it won't go. Touch the hand wheel and zoom away it went.
What I found out was that the commutator, brushes and their tubes was contaminated with oil. I carefully removed the brushes and cleaned them and the springs and caps with denatured alcohol, then used a q-tip with the alcohol to clean the commutator and brush tubes.
End of problem the machine works fine now.
Joe
I had that exact same thing happen with a 201. Sews fine, stop to do something, push on the controller it won't go. Touch the hand wheel and zoom away it went.
What I found out was that the commutator, brushes and their tubes was contaminated with oil. I carefully removed the brushes and cleaned them and the springs and caps with denatured alcohol, then used a q-tip with the alcohol to clean the commutator and brush tubes.
End of problem the machine works fine now.
Joe
#6
I am following along JIC I ever have a Featherweight. The part you mentioned does look weird to me. I count 6 wires? Wouldn't that be 2 for the lamp, 2 for the motor, 2 for the plug...then what is that other tidbit? Is it part frayed off of the nearest wire? Or is it a creepy spider? Once again...no real help here as I am pretty fresh at this, but watching to see what others have to say.
#9
#10
It's sort of that "give a man a fish feed him for a day, teach him to fish and he'll sit in a boat and drink beer all day." No wait. That's not it....
DonnaC,
I had that exact same thing happen with a 201. Sews fine, stop to do something, push on the controller it won't go. Touch the hand wheel and zoom away it went.
What I found out was that the commutator, brushes and their tubes was contaminated with oil. I carefully removed the brushes and cleaned them and the springs and caps with denatured alcohol, then used a q-tip with the alcohol to clean the commutator and brush tubes.
End of problem the machine works fine now.
Joe
I had that exact same thing happen with a 201. Sews fine, stop to do something, push on the controller it won't go. Touch the hand wheel and zoom away it went.
What I found out was that the commutator, brushes and their tubes was contaminated with oil. I carefully removed the brushes and cleaned them and the springs and caps with denatured alcohol, then used a q-tip with the alcohol to clean the commutator and brush tubes.
End of problem the machine works fine now.
Joe
I would also make sure that the belt isn't too tight. How's the temperature of the motor once it's been running a while?
Thread
Thread Starter
Forum
Replies
Last Post
Just Jan
For Vintage & Antique Machine Enthusiasts
41
10-29-2015 04:08 PM
quiltswithdogs
General Chit-Chat (non-quilting talk)
10
06-18-2009 07:52 AM