A greasy question
#12
Senior Member
Join Date: Apr 2012
Location: Jersey Shore
Posts: 528
Well, in my experience grease is internal therefore you'd rarely see it on cloth etc. It's the oil that usually makes the mess. I put enough grease so that the internal part of the gears are completely coated. I then wipe away excess with a q tip. Works for me, be it singer grease or triflow grease. Your mileage may vary.
#13
Super Member
Thread Starter
Join Date: Feb 2012
Posts: 8,091
Well, I've used up about 150 Q-tips cleaning a moderately grungy 500 tonight. When it goes back together it will be greased and oiled thoroughly but not excessively. I'm going to try to exercise .... um ..... restraint, that's it, restraint in my greasing.
We'll see how that goes.
Joe
We'll see how that goes.
Joe
#14
Power Poster
Join Date: Mar 2011
Location: Somewhere
Posts: 15,506
Well, I've used up about 150 Q-tips cleaning a moderately grungy 500 tonight. When it goes back together it will be greased and oiled thoroughly but not excessively. I'm going to try to exercise .... um ..... restraint, that's it, restraint in my greasing.
We'll see how that goes.
Joe
We'll see how that goes.
Joe
#15
Super Member
Thread Starter
Join Date: Feb 2012
Posts: 8,091
This is the first machine I really have used q-tips on. Other machines I just used tooth brushes, cloths, paper towels and the like.
In addition to the q-tips I used denatured alcohol to clean it. That stuff works pretty good. Drys fast and doesn't leave much residue or stains behind.
Of course it's not for little kids to use as they'd get stoned pretty quick on the vapors.
I got the 500 to sew so I checked with my LSMG and he said ............. yes I have the parts for it, I'll call you back Monday, too busy today. I figure I'll have it all cleaned and ready to finish up when he calls. Once back together I'll put it in a cabinet ( I have four sitting with no machines) and we'll use it. I've got all the cams it needs and about 80% of the attachments too. Of course the 401A and 4622 can share some of the feet and attachments with it so we're good to go here.
Joe
In addition to the q-tips I used denatured alcohol to clean it. That stuff works pretty good. Drys fast and doesn't leave much residue or stains behind.
Of course it's not for little kids to use as they'd get stoned pretty quick on the vapors.
I got the 500 to sew so I checked with my LSMG and he said ............. yes I have the parts for it, I'll call you back Monday, too busy today. I figure I'll have it all cleaned and ready to finish up when he calls. Once back together I'll put it in a cabinet ( I have four sitting with no machines) and we'll use it. I've got all the cams it needs and about 80% of the attachments too. Of course the 401A and 4622 can share some of the feet and attachments with it so we're good to go here.
Joe
#19
Super Member
Join Date: Dec 2011
Location: Northern CA near Sacramento
Posts: 1,107
Irishrose,
On the old vintage Singers the motors are lubed with grease, not oil. The clone motors are oiled, not greased.
On some of the clone motors there is a tiny hole on the housing just above or below the shaft, this is the oiling point.
If there is no oil hole on the clone motor I place a drop of oil on the shaft just as it enters the motor housing, then I run the motor full speed for 30 seconds or so to distribute the oil and then wipe off any extra oil.
More motors are ruined from over oiling than from under oiling.
Cathy
On the old vintage Singers the motors are lubed with grease, not oil. The clone motors are oiled, not greased.
On some of the clone motors there is a tiny hole on the housing just above or below the shaft, this is the oiling point.
If there is no oil hole on the clone motor I place a drop of oil on the shaft just as it enters the motor housing, then I run the motor full speed for 30 seconds or so to distribute the oil and then wipe off any extra oil.
More motors are ruined from over oiling than from under oiling.
Cathy
Joe, I'm too lazy to look up your post on which motors need greasing. The motor on my MW 15 clone seems like it would like some grease, but there are no ports on the top. Is it one that does need grease or are the ports elsewhere?
To answer your question, I grease my 301 lightly. I feel the movement of the gears will distribute it. I oil more heavily, but that machine seems to want it. The 404 I recently purchased is dirty with grease. I'll assemble your 'tool' list for cleaning it.
To answer your question, I grease my 301 lightly. I feel the movement of the gears will distribute it. I oil more heavily, but that machine seems to want it. The 404 I recently purchased is dirty with grease. I'll assemble your 'tool' list for cleaning it.
Thread
Thread Starter
Forum
Replies
Last Post
pumpkinpatchquilter
Main
10
07-20-2014 05:42 AM
Elisabrat
Main
9
07-10-2012 07:26 AM