The Machine That I Fiddled With Today
06-19-2015, 03:11 PM
#1131
Super Member
Join Date: Oct 2013
Location: Centralia, WA, USA
Posts: 4,890
Not really a machine as such. I'm starting to spend some time in my shop again. I've resumed work on a portable case I'm making to fit a full size Singer. The woodwork is all done. I'm just waiting to find an old briefcase or other case with latches and a handle I can rob for this case. New hardware is expensive and I'm trying to keep things cheap.
Maybe I can try my hand at some hardware too. The handle shouldn't be a big problem and there are other ways besides latches tie the top and bottom of the case together.
Might be a fun way to go.
Rodney
Maybe I can try my hand at some hardware too. The handle shouldn't be a big problem and there are other ways besides latches tie the top and bottom of the case together.
Might be a fun way to go.
Rodney
06-20-2015, 06:12 AM
#1135
Super Member
Join Date: Oct 2013
Location: Centralia, WA, USA
Posts: 4,890
I haven't had a featherweight case in hand to know how the handles were installed. The last case I built I took the handle off an old briefcase (nothing valuable-vinyl exterior but had decent hardware). The handle was riveted on on that one and I wasn't interested in preserving the case. I ripped the lining out then drilled the rivets to get the handle out. I then drilled out the rivets completely and tapped threads in the handle so I could screw the handle down on the new case. It worked for the briefcase but your featherweight case is likely to use a different style of handle.
I would probably use a razor or utility knife to carefully cut the lining on the inside of the featherweight case to access the fasteners for your handle. As long as you're careful you should be able to lift the liner out of the way enough to work then glue it back down when you're done. It might show a little but it would be better than replacing the whole liner.
I did a quick look at cases on the internet. It looks like at least a couple different styles of handles might have been used over the years. A lot depends on the style of handle Singer used and how it was mounted.
Rodney
I would probably use a razor or utility knife to carefully cut the lining on the inside of the featherweight case to access the fasteners for your handle. As long as you're careful you should be able to lift the liner out of the way enough to work then glue it back down when you're done. It might show a little but it would be better than replacing the whole liner.
I did a quick look at cases on the internet. It looks like at least a couple different styles of handles might have been used over the years. A lot depends on the style of handle Singer used and how it was mounted.
Rodney
06-20-2015, 03:15 PM
#1137
Senior Member
Join Date: Feb 2013
Location: Central Minnesota
Posts: 442
I haven't had a featherweight case in hand to know how the handles were installed. The last case I built I took the handle off an old briefcase (nothing valuable-vinyl exterior but had decent hardware). The handle was riveted on on that one and I wasn't interested in preserving the case. I ripped the lining out then drilled the rivets to get the handle out. I then drilled out the rivets completely and tapped threads in the handle so I could screw the handle down on the new case. It worked for the briefcase but your featherweight case is likely to use a different style of handle.
I would probably use a razor or utility knife to carefully cut the lining on the inside of the featherweight case to access the fasteners for your handle. As long as you're careful you should be able to lift the liner out of the way enough to work then glue it back down when you're done. It might show a little but it would be better than replacing the whole liner.
I did a quick look at cases on the internet. It looks like at least a couple different styles of handles might have been used over the years. A lot depends on the style of handle Singer used and how it was mounted.
Rodney
I would probably use a razor or utility knife to carefully cut the lining on the inside of the featherweight case to access the fasteners for your handle. As long as you're careful you should be able to lift the liner out of the way enough to work then glue it back down when you're done. It might show a little but it would be better than replacing the whole liner.
I did a quick look at cases on the internet. It looks like at least a couple different styles of handles might have been used over the years. A lot depends on the style of handle Singer used and how it was mounted.
Rodney
HelenAnn
Thread
Thread Starter
Forum
Replies
Last Post
SusieQOH
Links and Resources
2
11-18-2019 07:08 AM
AngieS
Main
13
10-05-2011 10:33 AM
craftybear
General Chit-Chat (non-quilting talk)
44
02-07-2011 08:50 PM
Izy
Pictures
25
05-25-2008 03:45 AM
