Originally Posted by LindaR
(Post 5404901)
Love the way the cabinet looks now...how do you flip her inside...do you have to take the wheel off?
Originally Posted by Monroe
(Post 5405022)
That is an amazing transformation! What did you use for the finish?
Editing: I just wanted to mention that all I did was remove the old lacquer, not "strip" it totally. I didn't have to sand anything except where I removed veneer and the bare wood needed to be smoothed or where I did some little veneer repairs. I have seen cabinets where stain was in the old shellac, not the wood, but this was not the case for this one. Hehe, someone saw a pic on my Facebook and said it looked "modern." I had to tell them that the 1950s are modern! :) |
4 Attachment(s)
Ok, here are some pics of the notch and crank that I had a request for more info on. Thought I'd post them here if anyone else was interested.
The notch is a little under an inch wide. It does still have sharp edges, which I intend to grind or file a little rounder and then paint. This should make them not as risky for catching your hand on accidentally. [ATTACH=CONFIG]352854[/ATTACH] [ATTACH=CONFIG]352855[/ATTACH] Here, most of my tape fix has been removed, and you can see the crank finger hits right at the edge of the notch when folded down. I think I notched it too deep, so the finger needs to be longer to stay in the wheel's notch. I think I'm going to put some heavy tubing around the finger to make a sleeve that goes past the end of the finger and will stay in the notch. [ATTACH=CONFIG]352856[/ATTACH] You can see the notch is just slightly wider than the crank finger. This is also the width of the bench grinder wheel I used to make it. [ATTACH=CONFIG]352857[/ATTACH] |
I wonder why no one has gotten a bunch of the replacement plates and then plated them. It's supposedly a relatively "easy" process. We could have a decent source for the plates, and not had to rob old machines for them.
Bennett, your machine and cabinet look incredible. That's one lucky lady! |
I really like how the cabinet looks! Neat how the different colors of wood look so sharp together. You can replace the handwheel on the 99 with a spoked wheel, and the crank finger will fit much better. You can find them on eBay for about $10, or some other sources. That is what we did to my 99, and it worked out perfect.
|
Originally Posted by ArchaicArcane
(Post 5409697)
I wonder why no one has gotten a bunch of the replacement plates and then plated them. It's supposedly a relatively "easy" process. We could have a decent source for the plates, and not had to rob old machines for them.
Bennett, your machine and cabinet look incredible. That's one lucky lady! I have one on my Singer 66- .... oh I forget which one, and my Sewmore 404. If you don't care about the difference in plating appearance, then it's no problem. Joe |
Wow, it arose from the ashes, to perfection!!!! Great job!!!
|
Originally Posted by J Miller
(Post 5410802)
There are a lot of places that sell reproduction slide and needle plates. They look pretty good with one exception. Their plating, although good doesn't match the originals. So you can tell at a glance they are repops.
I have one on my Singer 66- .... oh I forget which one, and my Sewmore 404. If you don't care about the difference in plating appearance, then it's no problem. Joe I've been told (OSMG) that the main reason that the chromed ones don't look right is that Singer didn't use chrome, they used nickel, but I haven't seen any shiny repros yet, only the dull that look,... wrong. The DH looked up the process of Nickelplating, when we found our model 27 face plate suddenly needing to be done, and said it wouldn't be too hard to do. It was basically polish, plate, polish again. The process he found didn't use electricity either (which did make me a little skeptical) I'd love to see a shiny repro... it might be good enough to sell a machine as whole if it's meant to be used, instead of "Here's your machine but you need to go find a slide plate" |
Love the cabinet and especially love the why you put the hand crank on. I was just gifted a 99 without a cabinet, I have to make a base for her, but I also want to make her a hand crank. Thanks for the information.
|
Nice job on both the machine and the cabinet. Love the two-tone look of the cabinet.
|
Love the work you did on the cabinet. What year was this machine made?
|
All times are GMT -8. The time now is 04:42 PM. |