Restoration - Wheeler & Wilson #8
#21
Banned
Thread Starter
Join Date: Oct 2012
Location: San Lorenzo, CA
Posts: 5,361
updates for today...
This is the spool pin and base, plus you can see a few shiny bolts
I have been following the idea that if when I clean it I see that it was shiny, I buff it, otherwise I leave it wire wheeled clean.
[ATTACH=CONFIG]392294[/ATTACH]
here is the needlebar, the presser bar, and the take-up assemblies all cleaned up, Brass springs again!
[ATTACH=CONFIG]392297[/ATTACH]
[ATTACH=CONFIG]392299[/ATTACH]
This is the spool pin and base, plus you can see a few shiny bolts
I have been following the idea that if when I clean it I see that it was shiny, I buff it, otherwise I leave it wire wheeled clean.
[ATTACH=CONFIG]392294[/ATTACH]
here is the needlebar, the presser bar, and the take-up assemblies all cleaned up, Brass springs again!
[ATTACH=CONFIG]392297[/ATTACH]
[ATTACH=CONFIG]392299[/ATTACH]
Last edited by SteveH; 02-01-2013 at 08:33 AM.
#23
Banned
Thread Starter
Join Date: Oct 2012
Location: San Lorenzo, CA
Posts: 5,361
ya know, I've worked with metal in one way or another for several decades, and I have to say that there REALLY IS a difference when working with old metal. Maybe it is the lack of "contains X% recycled materials" or my overly romantic imagination, but this metal seems to have nicer texture and seems to be more resistant to elements than modern metals.
#24
Sir Steve,
Well worth all the hours you have spent cleaning them. I love they way they clean up after decades of caked on dirt and oil. Don't know anything about the chemical compounds of metal from today versus a 100 years ago. Even with my lack of that knowledge, I can feel the difference in these vintage machines when using them for sewing. It's like their bones and souls are so much strong and smoother, like a good vintage.
Well worth all the hours you have spent cleaning them. I love they way they clean up after decades of caked on dirt and oil. Don't know anything about the chemical compounds of metal from today versus a 100 years ago. Even with my lack of that knowledge, I can feel the difference in these vintage machines when using them for sewing. It's like their bones and souls are so much strong and smoother, like a good vintage.
#25
I do not get to spend a lot of time on the computer, so I usually just look. However, I do enjoy enough to comment, and completely agree with all the others, especially vintagemotifs;
#26
Banned
Thread Starter
Join Date: Oct 2012
Location: San Lorenzo, CA
Posts: 5,361
Thanks again folks. I have been really busy for the last few days with making armor but I am done with that project and am back on the "old girls"
Trying to remove the pulley for this unit has proven to be the most challenging aspect yet..
There are two screws that set most of the components on this machine. The 2nd screw on the pulley is the one that goes into the keyway and prevents it from slipping. This screw would not move.
In order I tried:
1. Force - Screwdriver
2. Brute Force - bigger screwdriver
3. Brute Force with attitude - screwdriver with vice-grips clamped on them for leverage.
4. PB Blaster (rust eater)
5. Krud cutter
6. Heat
7. Heat and #3....
8. Drilled a hole in the center of the screw with a milling machine and used an "easy out" to remove it.
Drilling the hole in the middle of the old stripped screw
[ATTACH=CONFIG]393564[/ATTACH]
here is what is left of the screw with the pin that makes up the bottom of the screw.
[ATTACH=CONFIG]393566[/ATTACH]
Now, to reproduce the set screw...
Trying to remove the pulley for this unit has proven to be the most challenging aspect yet..
There are two screws that set most of the components on this machine. The 2nd screw on the pulley is the one that goes into the keyway and prevents it from slipping. This screw would not move.
In order I tried:
1. Force - Screwdriver
2. Brute Force - bigger screwdriver
3. Brute Force with attitude - screwdriver with vice-grips clamped on them for leverage.
4. PB Blaster (rust eater)
5. Krud cutter
6. Heat
7. Heat and #3....
8. Drilled a hole in the center of the screw with a milling machine and used an "easy out" to remove it.
Drilling the hole in the middle of the old stripped screw
[ATTACH=CONFIG]393564[/ATTACH]
here is what is left of the screw with the pin that makes up the bottom of the screw.
[ATTACH=CONFIG]393566[/ATTACH]
Now, to reproduce the set screw...
Last edited by SteveH; 02-06-2013 at 04:33 PM.
#28
Banned
Thread Starter
Join Date: Oct 2012
Location: San Lorenzo, CA
Posts: 5,361
turn out that I will not have to fab one up...
McMaster Carr sells them. (Hex head not slot screw but hey....)
http://www.mcmaster.com/#set-screws/=ldjyjn
McMaster Carr sells them. (Hex head not slot screw but hey....)
http://www.mcmaster.com/#set-screws/=ldjyjn
#29
Banned
Thread Starter
Join Date: Oct 2012
Location: San Lorenzo, CA
Posts: 5,361
so, here is a couple of shots that I took after putting together enough parts to get it off the kitchen table....(oops)
here is a normal light shot the shows the decorative plate and the remains of the bed designs
(Yes, they did bed designs on W&W #8's)
[ATTACH=CONFIG]393678[/ATTACH]
Here is the same shot under a flash. (Really brings out the details)
[ATTACH=CONFIG]393680[/ATTACH]
here is a full view. The band-aids on the glass presser foot are because the needle bar has NO resistance to up and down movements while disconnected from the drive line. The glass is already cracked, and I do not want it getting worse. (BTW - I am looking for glass inserts or additional feet, this one is a gathering foot...)
[ATTACH=CONFIG]393681[/ATTACH]
NOTE: The damage to the paint on the arm is going to be one of the bigger issues to overcome while trying to preserve the original details...
here is a normal light shot the shows the decorative plate and the remains of the bed designs
(Yes, they did bed designs on W&W #8's)
[ATTACH=CONFIG]393678[/ATTACH]
Here is the same shot under a flash. (Really brings out the details)
[ATTACH=CONFIG]393680[/ATTACH]
here is a full view. The band-aids on the glass presser foot are because the needle bar has NO resistance to up and down movements while disconnected from the drive line. The glass is already cracked, and I do not want it getting worse. (BTW - I am looking for glass inserts or additional feet, this one is a gathering foot...)
[ATTACH=CONFIG]393681[/ATTACH]
NOTE: The damage to the paint on the arm is going to be one of the bigger issues to overcome while trying to preserve the original details...
Thread
Thread Starter
Forum
Replies
Last Post
Wanabee Quiltin
Links and Resources
5
12-14-2013 07:50 AM
SteveH
For Vintage & Antique Machine Enthusiasts
7
02-01-2013 02:21 PM
Caroline S
For Vintage & Antique Machine Enthusiasts
10
06-07-2012 04:07 PM
ragqueen03
For Vintage & Antique Machine Enthusiasts
1
01-15-2012 08:00 PM
Nanamoms
For Vintage & Antique Machine Enthusiasts
6
12-04-2011 04:37 AM